Invacare P9000 service manual Folding Battery Tray for Transport Figure

Page 34

PROCEDURE 8

FWD WHEELCHAIRS

F

W

D

W

H

E

E

L

C H A I R S

WARNING

The Battery Box Retaining Strap MUST be fastened securely and adjusted properly to hold battery boxes in place before using the wheelchair.

6.Position retaining straps around each battery box as shown in FIGURE 19, clip retaining strap together and adjust if necessary.

NOTE: If wheelchair is equipped with shrouds, refer to REMOVING/INSTALLING SHROUDS in this procedure of the manual before connecting retaining strap together.

7.If necessary, install the Captain's Seat. Refer to REMOVING/INSTALLING CAPTAIN'S SEAT in PROCEDURE 9 of the owner's manual, part number 1080737.

Retaining

RetainingStrap Clip

Strap

Rear

Front Battery

Battery

Box

Box

Front of the

 

Battery Cable

Wheelchair

 

Wires (NEVER

Connector

pull to unplug.)

 

Battery Connections on

 

Side of Wheelchair Frame

 

NOTE: Wheelchair Frame not

 

shown for clarity.

 

FIGURE 19 - INSTALLING/REMOVING BATTERY BOXES

BATTERY TRAY

Folding Battery Tray for Transport (FIGURE 20)

1.Remove the battery boxes from the wheelchair. Refer toINSTALLING/REMOVINGBATTERYBOXESin this procedure of the manual.

Battery Pins

Tray

Pivot

FIGURE 20 - BATTERY TRAY - FOLDING BATTERY TRAY

FOR TRANSPORT

2.Lift up on the pin side of the battery tray and rotate UP towards the battery tray pivot.

3.Fold the wheelchair. Refer to ASSEMBLING EXCEL in this procedure of the manual.

Unfolding Battery Tray for Use (FIGURE 21)

1.Unfoldthewheelchair.RefertoASSEMBLINGEXCEL in this procedure of the manual.

2.Rotate the pin side of the battery tray DOWN towards the mounting slots on the hanger bracket.

WARNING

Make sure pins of battery tray are secure in the mounting slots of the hanger bracket, otherwise in- jury or damage may result.

3.Install the battery boxes. Refer to INSTALLING/ REMOVING BATTERY BOXES in this procedure of the manual.

Hanger

Bracket

Battery Tray

Pins

Mounting

Slots

FIGURE 21 - BATTERY TRAY - UNFOLDING BATTERY

TRAY FOR USE

Changing Width of Battery Tray (FIGURE 22)

NOTE: This procedure is only necessary when changing the width of the wheelchair.

1.Fold the battery tray. Refer to FOLDING BATTERY TRAY FOR USE in this procedure of the manual.

2.Remove the hex bolt and locknut that secure one (1) of the battery tray pins to the battery tray.

3.Refer to FIGURE 24 to determine mounting hole in the battery tray that corresponds to width of the wheelchair.

4.Reposition the battery tray pin to the mounting hole determined in STEP 3.

5.Secure the battery tray pin to the battery tray with the hex bolt and locknut.

6.Repeat STEPS 2-5 for remaining battery tray pin and two battery tray pivots.

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Excel and P9000 R N I N G E C I a L T E STable of Contents Specification S SpecificationsPower I F I C a T I O N SProcedure General Guidelines Repair or Service InformationBattery Charger Connector Digital Voltmeter Using Hydrometer to Check Battery Cells Lead Acid FigureTroubleshooting Procedure Field Load Test FigureNumber of Floating Balls Motor Testing FigureProcedure Troubleshooting Check charging systemCap Motor Pin Motor Connector OhmmeterCap Back Upholstery Washer Phillips Screw Replacing Back Upholstery FigureH O L S T E R Y Tie Wrap Mounting Hole Locknuts Washer Hex ScrewsSeat Frame Procedure Adjusting Seat Depth FigureAdjusting Back HEIGHT/ Replacing Back Canes Figure A T M EPreparing Mkiv Joystick for USE Figure Procedure ElectronicsMkiv Joystick Mounting Tube Adjustment Lock Lever Repositioning Mkiv Joystick FigureInstalling REMOVING/INSTALLING Drive Wheels FigureWheels Procedure Replacing Pneumatic TIRES/ Tubes Drive WHEELS/CASTERSReplacing Casters Figure Procedure WheelsReplacing Forks Figure Battery Terminals/Posts U1 Battery Box Bottom Dual 22 NF Batteries ProcedureT T E R I E S Dual U1 or Dual 22NF Battery Boxes Connecting Battery CablesT T E R Batteries Battery Clamp Battery Clamp Method Figures 4, 5Positive + Battery Terminal/Post Hex Nut CoverRED Battery Positive + Battery Terminal Post and Battery ClampR I E S A I R S Refer to Battery Tray in this proce- dure of the manualAssembling Excel Unfolding/Folding Integrated Sling Seat FigureUnfolding/Folding Captains Seat Figure Adjusting FLIP-UP Removable FootboardFWD Wheelchairs Push Brackets Pivot Link CrossbracesReplacing Armrest Plate Figure Replacing Armrest Pads FigureHeight Figure Replacing Captains Seat Figure Steps 7 Steps 3Steps 2 Replacing Wiring HarnessFWD Wheelchairs Procedure Steps 5Adjusting Limit Switch Figure Limit Switch Phono Plug Body Phono JackREMOVING/INSTALLING Shrouds Phillips Screws Locknut Installing Side Shrouds and FillersFiller Side Shroud Battery Box Battery Tray Phono Jack Retaining StrapChanging Seat Width Integrated Sling Seats Figure 16-18 orReplacing Crossbraces Captains Seat Figure SpacerLocknut Washer Steps 6 Pivot Link Hex BoltsHex Bolts Steps 6 Crossbrace SpacerCharging Batteries Figure When to Charge Batteries FigureDescription and Use of Battery Chargers Required ItemsCleaning Battery Terminals INSTALLING/REMOVING Battery Boxes FigureRecommended Battery Types Replacing BatteriesUnfolding Battery Tray for Use Figure Battery TrayFolding Battery Tray for Transport Figure Changing Width of Battery Tray FigureRemoving Battery Tray Figure Replacing Right Battery Tray Hanger Bracket FigureInstalling Battery Tray Figure Repositioning Motors Figure Footboard Mounting Bracket Battery Tray Hanger BracketReplacing Left Battery Tray Hanger Bracket Figure Spacer Hex ScrewUsers Weight 201 to 250 LBS Rotate battery tray hanger bracket upPin Steps 3 Replacing Clutch Handles FigureClutch Handle Clutch Handle Steps 9Steps 4 17, 18Unfolding/Folding the Wheelchair Assembling Power 9000 FigureRefer to INSTALLING/REMOV ING Footrests or Install Seat Rails GuidesRWD Wheelchairs Battery Discharge IndicatorWait until charging is complete Connect the battery box retaining strap clip together Retaining Strap ClipChanging Seat Width Figure Battery Tray Figure14-15, 16-18 Adjusting SEAT-TO-FLOOR Height H a I R SPhillips Screws To Controller DisassemblyReassembly From MotorsPlate Underside of Motor Mount Plate Alignment Pin Long SocketMotor Mount Alignment Hole Wheelchair Frame Support Tube Motor/GearboxLimited Warranty R R a N T YChedworth Way
Top Page Image Contents