Invacare 1125078 service manual Installing/Removing the Front Rigging Assembly, Front Riggings

Page 65

 

SECTION 10—FRONT RIGGINGS

 

 

Seat Frame Tube

New Mounting

Spacer

Screw

 

 

Locknut

Locknut

 

 

Spacer

 

 

Existing Mounting

 

Coved Washers

Screw

 

 

 

 

 

Front Rigging

 

Spacer

Support

 

Bracket

 

 

 

Front Seat

 

 

Support

 

 

Tube

 

 

Seat Frame Tube

 

*Large Mounting Hole

Spacer

Mounting Holes

on Front Riggings Support Bracket

DETAIL “A”

*Small Mounting Hole

Front Rigging

 

Support Bracket

Front Seat

Support Tube

*NOTE: Mounting hole arrangement on 16-inch wide seat shown. On the 18-inch wide seat, the mounting hole positions are reversed.

FIGURE 10.1 Installing/Removing the Front Rigging Support Brackets

Installing/Removing the Front Rigging Assembly

NOTE: For this procedure, refer to FIGURE 10.2 on page 66.

Installing

1.Turn the front rigging assembly to the side (open footrest is perpendicular to the wheelchair).

2.Insert the mounting pin on the front rigging assembly into the front rigging support bracket.

3.Rotate the front rigging assembly towards the inside of the wheelchair until it locks into place.

NOTE: The footplate will be facing the inside of the wheelchair when locked in place.

4.Repeat STEPS 1-3 for the other front rigging assembly.

5.If necessary, adjust the footrest height. Refer to Adjusting Footrest Height on page 66.

Part No. 1125078

65

At’m and At’m QT

Image 65
Contents At’m and At’m QT Wheelchair Type Electronics Manual Reference DocumentsReference Documents Table of Contents Arms Table of ContentsJoystick BatteriesANTI-TIPPERS Transporting the Wheelchair Limited WarrantyWheelchair TIE-DOWN Restraints and Seat Restraints Signal Word MeaningSpecial Notes At’m Label LocationAt’m QT Parameters Typical Product ParametersTypical Product Parameters Tire Pressure Repair or Service InformationGeneral Guidelines Batteries Operation InformationOxygen Charging Batteries Weight Limitation Weight TrainingGrounding Instructions Rain TestEMI Information EMI InformationEMI Information Checklist Safety INSPECTION/TROUBLESHOOTINGInformation Gauge and Diagnostics Codes TroubleshootingWheels Solutions WheelsDisplay Description Definition Comments SUB Code Diagnostics CodePossible Solution E05 E08 Motor/Gearbox/Brake Symptom Probable Cause SolutionsDamaged connector or worn Down, and recharge the wheelchair overnight with Troubleshooting Battery Troubleshooting Battery Charger DON’T Checking Battery Charge LevelField Load Test Field Load Test Battery QualityElectro-Mechanical Parking Brake Test Electro-Mechanical Parking Brake TestRemoving/Installing the Footboard Assembly Footboard AssemblyAdjusting Footboard Assembly Height InstallingSeat Removing/Installing the SeatRemoving/Installing the Seat Replacing Seat Positioning Strap Replacing Seat Positioning StrapRemoving/Installing Seat Upholstery Removing/Installing Under-Seat BasketRemoving/Installing Seat Upholstery Replacing the Seat Latches Replacing the Seat LatchesArms Removing/Installing Arm PadsReplacing Clothing Guard Removing/Installing Arm PadsRemoving/Installing Arm Tube Removing/Installing Arm TubeDisconnecting Disconnecting/Connecting the JoystickConnecting JoystickJoystick Removing/Installing the JoystickRemoving/Installing the Joystick Repositioning the Joystick to Opposite Arm Batteries Recommended Battery TypeRecommended Battery Type Removing/Installing the Battery Pack on the At’mRemoving/Installing the Battery Pack on the At’m Removing/Installing the Battery Box on the At’m QTRemoving/Installing the Battery Box on the At’m QT Negative Black Removing Removing/Installing the At’tm QT Battery Box Assembly Removing/Installing the At’tm QT Battery Box Assembly Charging Batteries Charging Using an Independent ChargerMulti-Function Charger Port At’m Resetting the Circuit BreakerAt’m QT 10 Resetting the Circuit Breaker At’mEngaging/Disengaging the Motors MotorsRemoving/Installing Motor Shroud Removing/Installing Motor ShroudRemoving/Installing the Base Plate Removing/Installing the Base PlateRemoving/Installing MK5 Controller Removing/Installing MK5 ControllerRemoving/Installing MK5 Controller Installing Removing/Installing the MotorsReplacing the Knurled Cylinder Removing/Installing the MotorsMotors Replacing the Knurled Cylinder Front Riggings Installing/Removing the Front Rigging Support BracketsFront Riggings Installing/Removing the Front Rigging AssemblyInstalling/Removing the Front Rigging Assembly Adjusting Footrest HeightReplacing Front Casters Wheels and CastersReplacing Forks Adjusting ForksReplacing Forks Adjusting Forks Removing/Installing the Drive WheelsReplacing Drive Wheels on the Drive Axle Removing/Installing the Drive WheelsANTI-TIPPERS Removing/Installing the Anti-TippersRemoving/Installing the Anti-Tippers- At’m Removing/Installing the Anti-Tippers- At’m QT Transporting the Wheelchair Transporting the WheelchairTransporting the Wheelchair USA Limited Warranty