Adcom A723, A720 manual Slot

Page 32

32

CHAPTER 4

Performing Advanced Functions

REMOTE	No.
EXAMPLE	RSSI 58
	193 RSSI 0
	#
	RSSI
	193 RSSI 44 58 0
	#
COMMAND	ID
APPLIES TO	A720, A720B, A723
DESCRIPTION	Sets/returns the node’s ID.
PARAMETERS	The node ID.
RETURNS	The node ID.
REMARKS	GET/SET.
REMOTE	Yes, SET only.
EXAMPLE	ID 4557
	193 ID 0
	#
	ID
	4557 ID 4557 0
	#
	6556 ID 7557
	6556 ID 0
	#
	Note: The last example shows a case where a remote node was
	instructed to change its own ID from 6556 to 7557. Even if it
	changed its ID, it answers with the old ID in order to cor-
	rectly ﬁnish the transaction.
COMMAND	SLOT
	CAUTION Changing these parameters may adversely affect the
	ability of the device to operate for extended periods under low
	solar radiation conditions.

Image 32

Contents ADC N ADC N Contents Contents Introduction What are addIT devices?Installation issues Conventions ItalicsChapter Using the Base Station Opening the packagesInstalling the base station Installing the receiverInstalling the power supply AddIT Power SupplyReplacing the fuse Conﬁguring the softwareUsing the RTU Installing the RTU Shows an addIT RTUShows what a typical RTU ﬁeld installation looks like More about the LED tool Conﬁguring an addIT RTU in the addVANTAGE software RTU batteryMaintaining and servicing the RTU Changing the battery Chapter Chapter Performing Advanced Functions Device series Understanding connectorsReceiver connector RTU connectors Pins on an I/O Connector Top ViewAddIT RTU Power Connector Top View Conﬁguring the devicesGeneral format of an answer General format of a commandSerial communication protocol SET Ownid nnnn Using terminal commandsSeries 1 devices SET Ownid SET PMP bl bhSET PMP 63 SET Slot 3600SET Rssi value SET Freq freq stepSET Freq 467112500 Querying the actual conﬁguration parameters SET RssiSeries 2 and 3 devices CmdsFreq Freq 433925000Freq Freq 433925000 25000Slot PMP PMP 65 72 193 cm193 CM 1 SSTDEV ReplDEL Repl 5667DEL Data 5666 12/12/1998 Data b1 b2 b3 ... bnDd mm yyyy hh mm ss si ft d1 d2 ... dn dd mm yyyy Dn csFrame 38 description Data 6367 30/4/1999 Frame 39 descriptionRoute DataImme Fdev InfoTemp = internalTem p Anlg Info 255 0 18/4/1999 21511 1.3 0 0 0 91146 900 Code Description Parameters Returns Sampling methods are deﬁned by three bits, as follows Return result depends on the control byte see table. However A720B and A723, but see also the comments in Remote on Performing Advanced Functions Command Code Deﬁnitions Port 193 TX 6789 Port 7/5/1999 183422193 RX 6789 B #234 BA#7851 BA 15190 BBlst 30/8/2001 160341 VERVER 1.3 VER 2.0Notiﬁcations Returned errors list Command line interpreterDevice descriptors and storage handler Real time clockNotiﬁcations Chapter Appendix. Speciﬁcations Parameter Min Typ Max UnitTransmitter all measurements made on a 50 Ω resistive load Chapter Chapter Index INFO, 41 OWNID, 26 PMP PMP What a base station contains Xmit Colophon Credits and ColophonCredits