Adcom A723, A720 manual Contents

Page 4

4

Contents

Installing the RTU _____________________________________ 14

More about the LED tool ____________________________ 16

Conﬁguring an addIT RTU in the addVANTAGE software 17 Maintaining and servicing the RTU_______________________ 17

The RTU battery ____________________________________ 17

Changing the battery _______________________________ 18

Chapter 4. Performing Advanced Functions_____________ 21

Device series _________________________________________ 22

Understanding connectors______________________________ 22

The receiver connector ______________________________ 22

The RTU connectors ________________________________ 23

Conﬁguring the devices ________________________________ 24

Serial communication protocol __________________________ 25

General format of a command _______________________ 25

General format of an answer _________________________ 25

Using terminal commands ______________________________ 26

Series 1 devices ____________________________________ 26

The SET series of commands ______________________ 26

Querying the actual conﬁguration parameters _______ 29

Series 2 and 3 devices ______________________________ 30

Notiﬁcations __________________________________________ 53

Returned errors list ____________________________________ 54

Command line interpreter ___________________________ 54

Device descriptors and storage handler _______________ 54

Real time clock _____________________________________ 54

Radio interface _____________________________________ 54

Notiﬁcations _______________________________________ 55

Appendix. Speciﬁcations ______________________________ 57

Index ________________________________________________ 61

Credits and Colophon_________________________________ 65

Image 4

Contents ADC N ADC N Contents Contents Introduction What are addIT devices?Installation issues Conventions ItalicsChapter Using the Base Station Opening the packagesInstalling the base station Installing the receiverInstalling the power supply AddIT Power SupplyReplacing the fuse Conﬁguring the softwareUsing the RTU Installing the RTU Shows an addIT RTUShows what a typical RTU ﬁeld installation looks like More about the LED tool Maintaining and servicing the RTU RTU batteryConﬁguring an addIT RTU in the addVANTAGE software Changing the battery Chapter Chapter Performing Advanced Functions Receiver connector Understanding connectorsDevice series RTU connectors Pins on an I/O Connector Top ViewAddIT RTU Power Connector Top View Conﬁguring the devicesSerial communication protocol General format of a commandGeneral format of an answer Series 1 devices Using terminal commandsSET Ownid nnnn SET Ownid SET PMP bl bhSET PMP 63 SET Slot 3600SET Freq 467112500 SET Freq freq stepSET Rssi value Querying the actual conﬁguration parameters SET RssiSeries 2 and 3 devices CmdsFreq Freq 433925000Freq Freq 433925000 25000Slot PMP PMP 65 72 193 cm193 CM 1 SSTDEV ReplDEL Repl 5667DEL Data 5666 12/12/1998 Data b1 b2 b3 ... bnDd mm yyyy hh mm ss si ft d1 d2 ... dn dd mm yyyy Dn csFrame 38 description Data 6367 30/4/1999 Frame 39 descriptionImme DataRoute Fdev InfoTemp = internalTem p 146 900 Info 255 0 18/4/1999 21511 1.3 0 0 0 91Anlg Code Description Parameters Returns Sampling methods are deﬁned by three bits, as follows Return result depends on the control byte see table. However A720B and A723, but see also the comments in Remote on Performing Advanced Functions Command Code Deﬁnitions Port 193 RX 6789 Port 7/5/1999 183422193 TX 6789 B #234 BA#7851 BA 15190 BBlst 30/8/2001 160341 VERVER 1.3 VER 2.0Notiﬁcations Returned errors list Command line interpreterDevice descriptors and storage handler Real time clockNotiﬁcations Chapter Appendix. Speciﬁcations Parameter Min Typ Max UnitTransmitter all measurements made on a 50 Ω resistive load Chapter Chapter Index INFO, 41 OWNID, 26 PMP PMP What a base station contains Xmit Credits Credits and ColophonColophon