Adcom A720, A723 manual Pmp

Page 33

	CHAPTER 4
	Using terminal commands
APPLIES TO	A720, A720B, A723
DESCRIPTION	Sets/returns the input storing and sampling intervals.
PARAMETERS	storage represents the time (in seconds) elapsed between two
	slots stored in the internal memory, while samples represents the
	numbers of samples used to build the average that will be stored.
RETURNS	The interval and rate.
REMARKS	The default storage is 900 (15 minutes) and samples is 3 (3 sam-
	ples per quarter of an hour).
REMOTE	Yes, SET only.
EXAMPLE	SLOT 900 3
	193 SLOT 0
	#
	SLOT
	193 SLOT 900 3 0
	#
	Note: The A720B base station needs only the rate. For consis-
	tency, however, it accepts both parameters and discards the
	one it doesn’t need.

33

COMMAND	PMP
APPLIES TO	A720, A720B, A723
DESCRIPTION	Sets/returns the node’s Power Management Parameters (switches
	on/off the battery charge).
PARAMETERS	The lower (switch on) and the higher limit (switch off), both in volts
	x 10. Standard Values are 65 (for 6.5 Volts) for switch on and 72 (for
	7.2 Volts) for switch off.
RETURNS	The lower (switch off) and the higher limit (switch on), both in volts
	x 10.
REMARKS	GET/SET.
REMOTE	Yes, SET only.
EXAMPLE	PMP 65 72
	193 PMP 0
	#

Image 33

Contents ADC N ADC N Contents Contents What are addIT devices? IntroductionInstallation issues Italics ConventionsChapter Opening the packages Using the Base StationInstalling the receiver Installing the base stationAddIT Power Supply Installing the power supplyConﬁguring the software Replacing the fuseUsing the RTU Shows an addIT RTU Installing the RTUShows what a typical RTU ﬁeld installation looks like More about the LED tool RTU battery Maintaining and servicing the RTUConﬁguring an addIT RTU in the addVANTAGE software Changing the battery Chapter Chapter Performing Advanced Functions Understanding connectors Receiver connectorDevice series Pins on an I/O Connector Top View RTU connectorsConﬁguring the devices AddIT RTU Power Connector Top ViewGeneral format of a command Serial communication protocolGeneral format of an answer Using terminal commands Series 1 devicesSET Ownid nnnn SET PMP bl bh SET OwnidSET PMP 63 SET Slot 3600SET Freq freq step SET Freq 467112500SET Rssi value SET Rssi Querying the actual conﬁguration parametersCmds Series 2 and 3 devicesFreq 433925000 FreqFreq Freq 433925000 25000Slot PMP 193 cm PMP 65 72193 CM 1 SSTRepl DEVRepl 5667 DELDEL Data b1 b2 b3 ... bn Data 5666 12/12/1998Dd mm yyyy hh mm ss si ft d1 d2 ... dn dd mm yyyy Dn csFrame 38 description Frame 39 description Data 6367 30/4/1999Data ImmeRoute Info FdevTemp = internalTem p Info 255 0 18/4/1999 21511 1.3 0 0 0 91 146 900Anlg Code Description Parameters Returns Sampling methods are deﬁned by three bits, as follows Return result depends on the control byte see table. However A720B and A723, but see also the comments in Remote on Performing Advanced Functions Command Code Deﬁnitions Port 6789 Port 7/5/1999 183422 193 RX193 TX #234 BA 6789 B#7851 BA 15190 BVER Blst 30/8/2001 160341VER 1.3 VER 2.0Notiﬁcations Command line interpreter Returned errors listDevice descriptors and storage handler Real time clockNotiﬁcations Chapter Parameter Min Typ Max Unit Appendix. SpeciﬁcationsTransmitter all measurements made on a 50 Ω resistive load Chapter Chapter Index INFO, 41 OWNID, 26 PMP PMP What a base station contains Xmit Credits and Colophon CreditsColophon