Adcom A723, A720 manual INFO, 41 OWNID, 26 PMP

Page 62

62INDEX

INFO, 41 OWNID, 26 PMP

series 1, 27 series 2, 33

PORT, 46

query parameters, 29 REPL, 35

ROUTE, 40 RSSI

series 1, 28 series 2, 31

RX

series 1, 29 series 2, 50

SLOT series 1, 27 series 2, 32

SST, 34

TIME, 30 TX, 50

VER

series 1, 29 series 2, 52

XMIT, 29

command line interpreter errors, 54 configuring

addIT RTU in addVANTAGE software, 17 addVANTAGE Lite software, 12 devices, 24

connectivity check, 14 connector

definition, 22 receiver, 22 RTU, 23

conventions, document, 7

D

DATA, 36

DEL, 36

DEV, 35 device

configuration, 24

descriptors and storage handler errors, 54 determining version, 22

operation time, 18 document conventions, 7 DUMP, 29

E

errors

command line interpreter, 54

device descriptors and storage handler,

54

radio interface, 54 real time clock, 54

F

FDEV, 41

field installation, RTU, 15 formats, 25

FREQ

series 1, 28 series 2, 31

I

ID, 32 IMME, 40 INFO, 41 install

power supply, 11–12receiver, 11

RTU, 14 installation issues, 6 internal battery, 17 introduction, 5

L

LED definition, 14 usage, 16

Image 62

Contents ADC N ADC N Contents Contents Introduction What are addIT devices?Installation issues Conventions ItalicsChapter Using the Base Station Opening the packagesInstalling the base station Installing the receiverInstalling the power supply AddIT Power SupplyReplacing the fuse Conﬁguring the softwareUsing the RTU Installing the RTU Shows an addIT RTUShows what a typical RTU ﬁeld installation looks like More about the LED tool Conﬁguring an addIT RTU in the addVANTAGE software RTU batteryMaintaining and servicing the RTU Changing the battery Chapter Chapter Performing Advanced Functions Device series Understanding connectorsReceiver connector RTU connectors Pins on an I/O Connector Top ViewAddIT RTU Power Connector Top View Conﬁguring the devicesGeneral format of an answer General format of a commandSerial communication protocol SET Ownid nnnn Using terminal commandsSeries 1 devices SET PMP 63 SET OwnidSET PMP bl bh SET Slot 3600SET Rssi value SET Freq freq stepSET Freq 467112500 Querying the actual conﬁguration parameters SET RssiSeries 2 and 3 devices CmdsFreq FreqFreq 433925000 Freq 433925000 25000Slot PMP 193 CM 1 PMP 65 72193 cm SSTDEV ReplDEL Repl 5667DEL Dd mm yyyy hh mm ss si ft d1 d2 ... dn dd mm yyyy Data 5666 12/12/1998Data b1 b2 b3 ... bn Dn csFrame 38 description Data 6367 30/4/1999 Frame 39 descriptionRoute DataImme Fdev InfoTemp = internalTem p Anlg Info 255 0 18/4/1999 21511 1.3 0 0 0 91146 900 Code Description Parameters Returns Sampling methods are deﬁned by three bits, as follows Return result depends on the control byte see table. However A720B and A723, but see also the comments in Remote on Performing Advanced Functions Command Code Deﬁnitions Port 193 TX 6789 Port 7/5/1999 183422193 RX #7851 BA 6789 B#234 BA 15190 BVER 1.3 Blst 30/8/2001 160341VER VER 2.0Notiﬁcations Device descriptors and storage handler Returned errors listCommand line interpreter Real time clockNotiﬁcations Chapter Appendix. Speciﬁcations Parameter Min Typ Max UnitTransmitter all measurements made on a 50 Ω resistive load Chapter Chapter Index INFO, 41 OWNID, 26 PMP PMP What a base station contains Xmit Colophon Credits and ColophonCredits