Adcom A723, A720 manual Return result depends on the control byte see table. However

Page 46

46

CHAPTER 4

Performing Advanced Functions

Following notiﬁcation types can be returned when issuing the

RNTTL command:

Value	Notiﬁcation Type

00	Notify On Positive Threshold.

01	Notify On Negative Threshold.

10	Notify if Out of Limits.

11	Notify if Inside the Limits.

RETURNS	The return result depends on the control byte (see table). However,
	whatever the return result is, it includes the control byte.
REMARKS	The general behavior is that an ANLG command issued on a cer-
	tain input channel will override any previous ANLG commands
	affecting that channel.
REMOTE	The A723 device cannot issue ANLG commands remotely, but can
	execute them.
EXAMPLE	For RSM
	ANLG 0
	9999 ANLG 0 5 5 5 5 5 5 5 5 4 4 5 5 0
	#
	For SSMAA (on channel 4)
	ANLG 68
	9999 ANLG 68 0
	#
	For DAN (on channel 0)
	ANLG 160
	9999 ANLG 160 0
	#
	For RNTTL (on channel 2)

ANLG 178

9999 ANLG 178 340 3900 0

#

For ENOPTR (on channel 10)

ANLG 202 1000 9999 ANLG 202 0

#

COMMANDPORT

Image 46

Contents ADC N ADC N Contents Contents Introduction What are addIT devices?Installation issues Conventions ItalicsChapter Using the Base Station Opening the packagesInstalling the base station Installing the receiverInstalling the power supply AddIT Power SupplyReplacing the fuse Conﬁguring the softwareUsing the RTU Installing the RTU Shows an addIT RTUShows what a typical RTU ﬁeld installation looks like More about the LED tool Maintaining and servicing the RTU RTU batteryConﬁguring an addIT RTU in the addVANTAGE software Changing the battery Chapter Chapter Performing Advanced Functions Receiver connector Understanding connectorsDevice series RTU connectors Pins on an I/O Connector Top ViewAddIT RTU Power Connector Top View Conﬁguring the devicesSerial communication protocol General format of a commandGeneral format of an answer Series 1 devices Using terminal commandsSET Ownid nnnn SET PMP 63 SET OwnidSET PMP bl bh SET Slot 3600SET Freq 467112500 SET Freq freq stepSET Rssi value Querying the actual conﬁguration parameters SET RssiSeries 2 and 3 devices CmdsFreq FreqFreq 433925000 Freq 433925000 25000Slot PMP 193 CM 1 PMP 65 72193 cm SSTDEV ReplDEL Repl 5667DEL Dd mm yyyy hh mm ss si ft d1 d2 ... dn dd mm yyyy Data 5666 12/12/1998Data b1 b2 b3 ... bn Dn csFrame 38 description Data 6367 30/4/1999 Frame 39 descriptionImme DataRoute Fdev InfoTemp = internalTem p 146 900 Info 255 0 18/4/1999 21511 1.3 0 0 0 91Anlg Code Description Parameters Returns Sampling methods are deﬁned by three bits, as follows Return result depends on the control byte see table. However A720B and A723, but see also the comments in Remote on Performing Advanced Functions Command Code Deﬁnitions Port 193 RX 6789 Port 7/5/1999 183422193 TX #7851 BA 6789 B#234 BA 15190 BVER 1.3 Blst 30/8/2001 160341VER VER 2.0Notiﬁcations Device descriptors and storage handler Returned errors listCommand line interpreter Real time clockNotiﬁcations Chapter Appendix. Speciﬁcations Parameter Min Typ Max UnitTransmitter all measurements made on a 50 Ω resistive load Chapter Chapter Index INFO, 41 OWNID, 26 PMP PMP What a base station contains Xmit Credits Credits and ColophonColophon