Adcom A720, A723 manual Fdev, Info

Page 41

			CHAPTER 4
			Using terminal commands
PARAMETERS	The destination node and the intermediate nodes, on the order
	starting from the issuing node to the traget (remote) node.
RETURNS	The actual routing table (in GET mode).
REMARKS	GET/SET.
REMOTE	No.
EXAMPLE	ROUTE 2419 10836
	16816 ROUTE 0
	#
	ROUTE
	16816 ROUTE
	2419	10836	0
	#
COMMAND	FDEV
APPLIES TO	A720, A720B, A723
DESCRIPTION	Formats the internal memory (destroys all the data).
PARAMETERS	None.
RETURNS	Nothing.
REMARKS	SET only.
REMOTE	Yes, SET only.
EXAMPLE	FDEV
	193 FDEV 0
	#

Note: Depending on the device’s memory size, this command may take several seconds to complete.

41

COMMAND	INFO
APPLIES TO	A720, A720B, A723
DESCRIPTION	Returns various status information.
PARAMETERS	None.
RETURNS	A list of a device’s internal variables:

Image 41

Contents ADC N ADC N Contents Contents What are addIT devices? IntroductionInstallation issues Italics ConventionsChapter Opening the packages Using the Base StationInstalling the receiver Installing the base stationAddIT Power Supply Installing the power supplyConﬁguring the software Replacing the fuseUsing the RTU Shows an addIT RTU Installing the RTUShows what a typical RTU ﬁeld installation looks like More about the LED tool Conﬁguring an addIT RTU in the addVANTAGE software RTU batteryMaintaining and servicing the RTU Changing the battery Chapter Chapter Performing Advanced Functions Device series Understanding connectorsReceiver connector Pins on an I/O Connector Top View RTU connectorsConﬁguring the devices AddIT RTU Power Connector Top ViewGeneral format of an answer General format of a commandSerial communication protocol SET Ownid nnnn Using terminal commandsSeries 1 devices SET PMP bl bh SET OwnidSET PMP 63 SET Slot 3600SET Rssi value SET Freq freq stepSET Freq 467112500 SET Rssi Querying the actual conﬁguration parametersCmds Series 2 and 3 devicesFreq 433925000 FreqFreq Freq 433925000 25000Slot PMP 193 cm PMP 65 72193 CM 1 SSTRepl DEVDEL Repl 5667DEL Data b1 b2 b3 ... bn Data 5666 12/12/1998Dd mm yyyy hh mm ss si ft d1 d2 ... dn dd mm yyyy Dn csFrame 38 description Frame 39 description Data 6367 30/4/1999Route DataImme Info FdevTemp = internalTem p Anlg Info 255 0 18/4/1999 21511 1.3 0 0 0 91146 900 Code Description Parameters Returns Sampling methods are deﬁned by three bits, as follows Return result depends on the control byte see table. However A720B and A723, but see also the comments in Remote on Performing Advanced Functions Command Code Deﬁnitions Port 193 TX 6789 Port 7/5/1999 183422193 RX #234 BA 6789 B#7851 BA 15190 BVER Blst 30/8/2001 160341VER 1.3 VER 2.0Notiﬁcations Command line interpreter Returned errors listDevice descriptors and storage handler Real time clockNotiﬁcations Chapter Parameter Min Typ Max Unit Appendix. SpeciﬁcationsTransmitter all measurements made on a 50 Ω resistive load Chapter Chapter Index INFO, 41 OWNID, 26 PMP PMP What a base station contains Xmit Colophon Credits and ColophonCredits