Toshiba H-9100N-CA, EO1-32003BE Weighing Operation, Menu REG., M.DOWN, or Rewrap Mode Weigh

Page 66

1/2 lb

13. OPERATING PROCEDURES

13.1 WEIGHING OPERATION

13.1 WEIGHING OPERATION

Menu: REG., M.DOWN, or REWRAP

Mode: WEIGH

The weigh mode is used to weigh a commodity and to issue labels. The label contains data such as a weight, unit price (price per weight) and total price (calculated as a result of the weighing operation). The following is a basic operation seen at the sales floor of a store or at a back room where different kinds and weights of commodities are repacked. Pressing the VOID key subtracts the last entry from the memory.

Example) When PLU #100 and an unit price of $8.00 are set in the speed key #12.

Enter the PLU #.

1

0

0

LB

kg

The unit of measure can be changed for CA/QR model only.

LB Ö kg

Press :	PLU	Press the	12
		speed key.

Available only when the initial setting # 5-6 is set to 1.

lb scale

kg scale

100			<REG.> MENU	WEIGH
100	1/4	1/2	T-BONE STEAK
g	1/4	1/2	T-BONE STEAK
g
				lb	UNIT/$	TOTAL $
				1.000	8.00	8.00
Place a commodity
on the platter.
(Ex. 1.000 lb.)

MANUAL :	PRT	AUTO
MANUAL :	:	AUTO
	*

The label is issued

Press when canceling	VOID
the last sales.

TEC STORE

(TEL) 0123-45-6789

(Sample label)

NOTES:

1. Pressing the speed key to which no PLU data has been assigned will result in an error. In this case, press

the C key, then press the speed key to which PLU data has been assigned.

2.To change between AUTO and MANUAL, follow the procedure provided in section 13.9.

3.If a unit price exceeding 4 digits is obtained by multiplying by 2 or 4 (when pressing the key), the unit price will be 0.

key or

1/4 lb

4.	100 g	key is available only when the scale is a kg scale or operated on kg base.
5.	When	the	1/2 lb	,	1/4 lb	or	100 g	key is pressed, the unit price does change on the display.

6.When the “compulsory tare” is selected, a tare must be subtracted in a weighing operation, otherwise an error message “TARE REQUIRED” will be displayed when the following operation has been done:

① Manual mode: Pressing the PRT/* key.

②Auto mode: Placing a commodity on the platter.

③ Floating vendor mode: Pressing the Vendor key.

When a “TARE REQUIRED” is displayed, refer to Section 13.6 to follow the proper weighing procedure.

13- 2

Image 66

Contents 9100N-US/CA Page Safety Summary Precautions Table of Contents Toshiba TEC Introduction Accessories Applicable Model1 0 0 5 0 L N F F B U S Specification ScaleSTLAN-2P OptionLON ESD-SR-15Appearance PC-ATCA Type DisplayUS Type Front Display PanelKEY Layout Programming KeyboardProgramming Keyboard Function Space SendProg Operation Keyboard and Speed Keyboard Operation Keyboard FunctionPLU DT/TM SaveFor LogoFeed ZeroProcedure Before Operation Speed KEY SETLevel Adjustment Removal and Replacement of RECEIPT/LABEL Media Guide Main Menu Password InputOutline of Operation MenuProgramming Procedures How to access to Programming MenuTitle and Contents of Programming Menu How to enter characters Unit Price Change MenuPLU Data Setting For the UPC#Auto Code Ingredient Message Nutrition Facts Key advances to the next menu. Pressing the ↑ Daily Value Max digits Contents of Daily value Set the Daily Value TableDeleting Nutrition Data Memory file sortVerification label is issued PLU Verifying LabelAddress and Commercial Message Setting Combination Message Message construction Message display timeThank YOU ANK YOU Call AGA Thank YOUThank YOU Call ANK Y Thank YOUSpecial Information Grade LineSpeed KEY Setting Setting Department/Vendor NumberESC Menu Print Format By pressing KeyLabel Format Number Table Format NoDATE/TIME Setting CMT OperationsPL-3 Operation Transmission Item List Item #CMT Transmission Delay Time Table IN-LINE/LOCALLON System Cancel Retry Continue Data TransmissionDefault Bar Code Format BAR Code FormatUPC # Flag PLU # UPC # PC/D Price Weight PLU # UPC # PC/DTitles Transferring Logo Data Display Label Receipt Print Logo 320 x 118 dotsError message for data transmission Idiom Setting Vendor SettingFree Format Setting Key functionsOFF 10-33 SP-INFO/NET WT 10-35 Dots Total height 670 dots Dot size Dot size of the thermal head is 0.125mm square How to access Report menu Programmed Data Verification ReportsFor Password Security Setting Password and Protect MenuR S X Z ESC Calling Menu by Entering Password Operating Procedures How to access REG., M.DOWN, or Rewrap menuMenu REG., M.DOWN, or Rewrap Mode Weigh Weighing OperationFIX Price Operation for US Type only By Count Operation REG. Menu BY-COUNT DonutsFor Print Count Operation Example B When operating in Fix or By Count mode Set the number of labels. Max labels Enter the PLU # Issuing Labels with NET Weight Statement for US Type only Sample label TARE/SAVE Function Procedures SaveCalling and Printing Grade Lines Calling and Printing Logos Menu REG, M.DOWN, or Rewrap Mode WEIGH, FIX, or by Count Selecting Print ItemDate Change Batch Print Mode with 30 Items Run Assignment Changing a Unit Price and Calling G.Line/LOGO Stopping or Canceling Label Issue Visual Commodity Library Dpt #Floating Vendor UNIT/$ Total $Price deletion SubtotalHow to access Report or Reset menu Total OperationHourly Total Report Grand Total ReportPLU Total Report Vendor Total Report Error Message Table Programming ModeLabel lssue Mode Report and Reset ModeLON System Mode Cleaning the Print Head Troubleshooting Before You Call for ServicePage