Panasonic MC-V5210 manuel dutilisation Replacing Belt

Page 30

		Replacing Belt
			➢ Replace belt whenever a burning
				rubber smell caused by excessive
				slippage occurs.
	Belt Cover
	Couvercle de		➢	Remove lower plate.
	la courroie		➢	Remove lower plate.
	la courroie
	Cubierta de
	la banda		➢	Lift rear belt cover and remove
		Lift Agitator Up	➢	Lift rear belt cover and remove
	Agitator Holder	Lift Agitator Up		agitator holder.
	Agitator Holder	Soulever l’agitateur
	Support de l’agitateur	Soulever l’agitateur
	Support de l’agitateur	Unidad del agitador
	Soporte de l’agitador	Unidad del agitador
	Soporte de l’agitador		➢ Remove agitator by carefully lifting
			➢ Remove agitator by carefully lifting
				out.
			➢ Remove worn or broken belt.
	Motor Shaft		➢ Clean agitator.
	Arbre d’entraînement	Install
	du moteur	Install
	du moteur	New Belt
	Eje del motor	New Belt
	Eje del motor	Poser la	➢	Loop new belt (Panasonic Type UB8
		Poser la
		nouvelle
		nouvelle		only) around motor shaft and
		courroie		only) around motor shaft and
		Instalación		agitator pulley.
		de la correa
			➢ Reinstall agitator back into nozzle
				housing grooves.
			➢ Close rear belt cover and reinstall
				agitator.
	Groove		➢ After reinstalling the agitator, turn it
	Groove			by hand to make sure that belt is not
	Ouverture			by hand to make sure that belt is not
	Ouverture			twisted or pinched and that all
	Ranura			twisted or pinched and that all
	End Cap			rotating parts turn freely.
	Bouchon
	Tapa de		➢	Reinstall lower plate. (See Removing
	extremo		➢	Reinstall lower plate. (See Removing
	extremo			and Installing Lower Plate, page 28).
				and Installing Lower Plate, page 28).

- 30 -

Image 30

Contents MC-V5210 To OUR Valued Customer Please PAY Close Attention to ALLRenseignements importants Notre ClientèleAdvertencia Cuidado Important Safety Instructions Avertissement Conserver CES InstructionsInstrucciones importantes de seguridad Table of Contents Table des matières Tabla de contenidoGrounding Instructions Advertencia Identificación de piezas Feature Chart Assembly Attaching HandleMontage du manche Colocación del mangoTool Storage Rangement des accessoires Almacenaje de herramientasEdge Cleaning Motor ProtectorProtecteur du moteur Nettoyage latéralLimpieza para orillas Protector del motorON-OFF Switch Handle AdjustmentsRéglage de l’inclinaison du manche InterrupteurControl ON-OFF Ajustes del mangoUsing Tools Tool UsageUtilisation des accessoires Emploi des accessoiresUso de herramientas Routine Care of Vacuum Cleaner Replacing Secondary Hepa FilterRemplacement du filtre secondaire de type Hepa Cambiar el filtro de Hepa secundarioChanging Dust Bag Remplacement du sac à poussière Cambio de la bolsa para polvoRemoving and Installing Lower Plate Tabs LatchesEnlèvement et installation de la Plaque inférieure Quitar y ensamblar la base inferiorReplacing Belt Remplacement de la courroie Cambio de la correaCleaning Agitator Replacing BrushesLimpieza del agitador Remplacement des brossesNettoyage de l’agitateur Cambio del agitadorAgitator Assembly Cleaning Exterior and ToolsNettoyage du boîtier et des accessoires Assemblage de l’agitateur / Montaje de agitadorLimpieza del exterior y de los Herramientas Removing Clogs Dégagement des obstructions Quitando los residuos de basura en Los conductosBefore Requesting Service Guide de dépannage Antes de pedir servicio Warranty Limitations and Exclusions Garantie Garantía Page Page Page What to do When Service is Needed What to do when service is needed Service après-vente Canada