Panasonic MC-V5210 manuel dutilisation Cleaning Agitator, Replacing Brushes

Page 32

Cleaning Agitator

➢

➢

➢

➢

➢

➢

Clean agitator after every five uses and every time the belt is replaced.

Remove lower plate.

Cut off any carpet pile and lint entangled around agitator with a pair of scissors.

Remove agitator.

Remove any string or debris located on the end caps, washers or agitator shaft.

Reinstall agitator and lower plate.

Replacing Brushes

Card

Carte

Tarjeta

E-Clip

Bride en E

Sujetador de E

Agitator Shaft

Arbre d’entraînement	Right End Cap
Eje del agitador	Bouchon droit
	Tapa del extremo
	derecho

	Agitator Pulley	Agitator Holder
		Support de l'agitateur
	Poulie de l’agitateur
		Soporte del agitador
	Polea del agitador

Push Off

Pousser

Empuje hacia fuera

Brush

Brosse

Cepillo

➢When the bristles on the agitator are worn so that they do not touch a card held across the lower plate, the brushes should be replaced.

➢Remove lower plate and agitator.

➢Remove the E-clip from agitator shaft and end cap.

➢Do not bend agitator shaft or lose E- clip or spacer.

➢Pull agitator shaft out of agitator body.

➢Pull, or pry out, agitator holder and agitator pulley.

➢Push each brush out of agitator body as shown.

➢Install new brushes by reversing procedure.

➢Reinstall agitator holder and agitator pulley completely.

➢Reinstall the agitator shaft, end cap and E-clip.

➢See exploded view for correct assembly of parts.

➢Position belt over agitator pulley on the agitator.

➢Reinstall agitator and lower plate.

- 32 -

Image 32

Contents MC-V5210 To OUR Valued Customer Please PAY Close Attention to ALLRenseignements importants Notre ClientèleAdvertencia Cuidado Important Safety Instructions Avertissement Conserver CES InstructionsInstrucciones importantes de seguridad Table of Contents Table des matières Tabla de contenidoGrounding Instructions Advertencia Identificación de piezas Feature Chart Assembly Attaching HandleMontage du manche Colocación del mangoTool Storage Rangement des accessoires Almacenaje de herramientasEdge Cleaning Motor ProtectorNettoyage latéral Limpieza para orillasProtecteur du moteur Protector del motorON-OFF Switch Handle AdjustmentsInterrupteur Control ON-OFFRéglage de l’inclinaison du manche Ajustes del mangoUsing Tools Tool UsageUso de herramientas Utilisation des accessoiresEmploi des accessoires Routine Care of Vacuum Cleaner Replacing Secondary Hepa FilterRemplacement du filtre secondaire de type Hepa Cambiar el filtro de Hepa secundarioChanging Dust Bag Remplacement du sac à poussière Cambio de la bolsa para polvoRemoving and Installing Lower Plate Tabs LatchesEnlèvement et installation de la Plaque inférieure Quitar y ensamblar la base inferiorReplacing Belt Remplacement de la courroie Cambio de la correaCleaning Agitator Replacing BrushesRemplacement des brosses Nettoyage de l’agitateurLimpieza del agitador Cambio del agitadorAgitator Assembly Cleaning Exterior and ToolsLimpieza del exterior y de los Herramientas Nettoyage du boîtier et des accessoiresAssemblage de l’agitateur / Montaje de agitador Removing Clogs Dégagement des obstructions Quitando los residuos de basura en Los conductosBefore Requesting Service Guide de dépannage Antes de pedir servicio Warranty Limitations and Exclusions Garantie Garantía Page Page Page What to do When Service is Needed What to do when service is needed Service après-vente Canada