A&D SW-15KS, SW-6KS, SW-30KM, SW-60KL, SW-60KM, SW-150KM, SW-15KM, SW-150KL OP-03 Specifications, Ascii

Page 30

1.Disconnect the AC power cable from the electrical outlet. When the battery is installed, make sure that the scale is turned OFF.

2.Loosen the M4 screws and remove the rear cover of the display.

Note: Take care not to drop the display.

3.Connect the cables to the external device through the cable gland to the terminal blocks on the interface board.

4.Attach the connector cables (7 and 10 pins), provided with OP-03, to the connectors on the interface board and the connectors on the main board inside the display.

5.Secure the interface board using the two M3 x 8 screws provided with OP-03.

6.Tighten the cable glands and attach the rear cover to the display and secure it with the screws loosened at step 2.

7.Connect the AC power cable to the electrical outlet.

8.Set the function settings “bp5”, “btpr”, “prt”. “5if” and “aCk” as necessary.

‰To use the OP-03 RS-232C, the function setting of “5if” must be set to “0”.

13.2.2. OP-03 Specifications

RS-232C interface

 

 

Transmission form

Asynchronous, bi-directional, half-duplex

Data format

Baud rate:

2400, 4800, 9600 bps

 

Data bits:

7 bits + parity 1bit (EVEN / ODD)

 

 

or 8 bits (non parity)

 

Start bit:

1 bit

 

Stop bit:

1 bit

 

Code:

ASCII

 

Terminator:

CRLF (CR:0Dh, LF:0Ah)

 

 

 

 

LSB

 

 

 

 

 

MSB

 

 

 

 

 

 

 

 

0

1

2

3

4

5

6

 

 

 

 

 

 

 

 

 

 

 

Start

 

bit

 

Data bits

 

Parity

 

bit

 

 

 

 

1(-15V~-5V)

0(5V~15V)

Stop bit

Relay output

The maximum rating of the replay output is as follows.

‰ Maximum voltage:

50V DC

‰ Maximum current:

100 mA DC

‰ Maximum ON resistance:

8 Ω

28

Page 29 Page 31
Image 30
Page 29 Page 31
Contents SW Series Page Contents Options MaintenanceSpecifications Gravity Acceleration MAPCompliance Compliance with FCC rulesClassification of protection provided by enclosures Features IntroductionCleaning the scale PrecautionsInstalling the scale Operating the scaleUnpacking Description of Each Part Display rear sideSymbol Description Display and symbolsSymbols DisplaySwitches Setting UP Attaching the display pole to the baseSW-M / L series with a display pole Installing the scale Bat oo Turning the power on and OFFBasic Operation ON/OFFBasic weighing operation Indicator will not turn onSelecting a weighing unit During the Tare operationWeight display resolution Counting Mode PrintFormula to compare Five-level comparator modeComparator LoloThree-level comparator mode Five-level comparator mode Three-level comparator mode Entering the comparator valuesPrint Sample Tare Calibration Gravity acceleration correctionCalibration using a weight Units PrintRestoring the factory set values Setting the parameters FunctionsTare ON/OFF Function list Key Using the OP-02 SLA battery Installing the batteryOptions Charging the battery Installing OP-03 OP-03 RS-232C / Relay OutputOP-03 Specifications AsciiSolid sate relay ‰ Data example Command mode Stable positive data Page Installing OP-04 OP-04 RS-422OP-04 Specifications Example of connection RS-422 Stable data Maintenance Error codesSpecifications SpecificationsModel SW-6KS SW-15KS SW-15KM SW-30KM Model SW-60KM SW-60KLExternal dimensions SW-60KL / SW-150KL with a display pole Gravity Acceleration MAP Values of gravity at various locationsWorld map
Top Page Image Contents