Radio Shack 43-3872 manual Setting a PIN Code, Setting the Ring Time

Page 60

The Integrated Answering Device

2.Once you have recorded a personal greeting, press the CHANGE soft key to choose the greeting. The selected outgoing message is played. Each time you press the CHANGE soft key, the phone switches the outgoing message between the prerecorded and the personal outgoing message.

Setting a PIN Code

Security code selects a two-digit Personal Identification Number (PIN) code. A PIN code is required to play your messages from a remote location.

1.Press MENU/DEL (or the MENU soft key on the base). Select the Answ. Setup menu, and then the Security Code submenu.

2.Enter a two-digit PIN code (01-99) using the number keypad (0-9) (default is 80).

3.Press SELECT/ (or the OK soft key on the base). You will hear a confirmation tone.

Setting the Ring Time

Ring Time allows you to set the number of rings the caller hears before your answering system plays the outgoing message. You can set the ring time to answer after two, four, or six rings. If you enable the Toll Saver (TS), the answering system picks up after two rings if you have new messages and after four rings if there are none.

1.Press MENU/DEL (or the MENU soft key on the base). Select the Answ. Setup menu, and then the Ring Time submenu.

60

Image 60

Contents 4GHz Expandable Corded/Cordless Phone Answerer Contents Introduction Information FCC StatementImportant Information Surge Protection Important Safety Instructions Read this Before Installation Important Caller ID InformationInstallation Selecting a LocationOn a Desk Top You must useOn a Wall Plate or Wall Using AC Power CONNECTING/CHARGING the Battery Pack Recharging the Battery Pack Installing the Beltclip Using a HeadsetTo attach the beltclip To remove the beltclipExample of the standby mode display Handset Display and IconsSoft KEY Functions Base 570#Setting Menu Options Using the InterfaceDirectLink Mode Using DirectLink Mode Handset onlyUsing Room/Monitor Room/Baby MonitorHandset Setup/Base Setup Selecting a Ringer ToneDistinctive Ringer Setup Setting the Anykey Answer Handset only Selecting a LanguageSetting the Key Touch Tone Global Setup Setting Day and TimeSetting Cidcw Caller ID on Call Waiting Setting the Area Code Setting the Dial ModeSystem Reset Handset only De-register the HandsetPlace handset on main base Handset RegistrationUsing Your Phone Power Failure OperationMaking a Call From the handsetReceiving a Call From the Handset SpeakerphoneFrom the base Switching to Speakerphone During a Call Hanging UPCall Waiting Placing a Call on Hold RedialingRinger volume Earpiece and Speaker VolumeAdjusting the RINGER, Earpiece and Speaker Volume Audio Tones Base onlyDo Not Disturb DND Temporarily Muting the RingerMuting the Ringer Tone Dialing SWITCH-OVER Mute MicrophoneTraveling OUT Range Booster Handset OnlyPrivacy Mode ConferencingJoining a Conference Call Find Handset Speed DialingFrom a second handset Phonebook PhonebookIf you make a mistake while entering a name Store/Edit No. appears Storing Caller ID Messages in the Phonebook Storing a Redial RecordDeleting a Redial Record Viewing the PhonebookMaking Calls Using the Phonebook From Standby Mode Deleting ALL Phonebook Locations Base only From the handset Copying Phonebook LocationsTesting Stored Emergency Number From the baseCaller ID and Cidcw Caller ID on Call Waiting Incomplete DataCall Waiting Deluxe Features Viewing the Caller ID List Deleting Information from the Caller ID List Deleting ALL Caller ID NAME/NUMBERSFrom Standby Mode From Talk modeCalling a Party from the Caller ID List Expanding Your Phone Four Multi-Handset ExpandabilityRegister the Handset to the Base Using the Directlink Mode DirectLink callINTERCOM/CALL Transfer Feature IntercomFOUR-WAY Conferencing Making an Intercom From a handsetCall Transfer Feature Answering an IntercomAnswering a Call Transfer To answer a page from a handsetAccepting the call transfer To answer a page from the baseFeatures Integrated Answering DeviceAnswering System Setup Record a Personal Outgoing Message Base OnlySelecting Your Greeting Base only Setting a PIN Code Setting the Ring TimeSetting the Record Time Setting the Message Alert On or OffSetting the Language of your Answering System Setting the Call ScreenTurning the message alert tone off by pressing any key Turning the message alert tone off from a remote locationUsing Your Answering System Turning the Answering System ON/OFFNew Message LED Playing your messagesRepeating a message Skipping a message Deleting a message Voice memo Recording a conversationRemote access away from home Remote OperationFunction Remote access with the handset Remote Key FunctionAnsweringMachine operation appears on the base Integrated Answering Device Troubleshooting Symptom SuggestionKeep the handset away from microwave ovens Service and Repair CareMemo RadioShack Corporation