Radio Shack 43-3872 manual Remote access away from home, Remote Operation

Page 68

The Integrated Answering Device

Ô NOTES Ô

Time stamp will not be heard until you have set the time. See “Setting

Day and Time” on page 24.

The system will only playback messages for four minutes and then it returns to the command waiting mode. To continue playing your messages, press 0 then 2 again within 15 seconds.

If you enter an incorrect PIN code three times, you will hear a beep and the system will return to standby.

During the remote operation,

“Line Remote” appears on the handset.

If the answering system is recording an incoming message, the recording operation is canceled when you start remote

From the handset

1.While on a call, press MENU/DEL.

2.Press to move the pointer to Call Record, and then SELECT/ .

Recording a Call and R appear in the display.

To turn stop recorging, repeat above step again, Stop Recording appears.

REMOTE OPERATION

You can check, play, or delete messages, even record a new greeting message from a remote location (when you are away from home, or from another room using a handset). Additionally, you can turn On or Off your answering system remotely. Ô

Remote access away from home

You can operate your answering system from a remote location using any touch-tone telephone.

1.Call your telephone number and wait for the system to answer. If the answering system is off, it will answer after about ten rings and sounds a series of beeps.

2.During the greeting message (or a series of beeps when the answering system is off), press 0 and enter your PIN code within two seconds (see

“Setting a PIN Code” on page 60).

3.The answering system announces the current time and the number of messages stored in memory. You hear “To play incoming messages, press zero-two. For help, press one-zero”. You will hear a beep.

4.Enter a command within 15 seconds, each command there after must be

68

Image 68
Contents 4GHz Expandable Corded/Cordless Phone Answerer Contents Introduction Information FCC StatementImportant Information Surge Protection Important Safety Instructions Read this Before Installation Important Caller ID InformationInstallation Selecting a LocationOn a Desk Top You must useOn a Wall Plate or Wall Using AC Power CONNECTING/CHARGING the Battery Pack Recharging the Battery Pack Installing the Beltclip Using a HeadsetTo attach the beltclip To remove the beltclipExample of the standby mode display Handset Display and IconsSoft KEY Functions Base 570#Setting Menu Options Using the InterfaceDirectLink Mode Using DirectLink Mode Handset onlyUsing Room/Monitor Room/Baby MonitorHandset Setup/Base Setup Selecting a Ringer ToneDistinctive Ringer Setup Setting the Anykey Answer Handset only Selecting a LanguageSetting the Key Touch Tone Setting Cidcw Caller ID on Call Waiting Global SetupSetting Day and Time Setting the Area Code Setting the Dial ModeSystem Reset Handset only De-register the HandsetPlace handset on main base Handset RegistrationUsing Your Phone Power Failure OperationMaking a Call From the handsetFrom the base Receiving a CallFrom the Handset Speakerphone Call Waiting Switching to Speakerphone During a CallHanging UP Placing a Call on Hold RedialingRinger volume Earpiece and Speaker VolumeAdjusting the RINGER, Earpiece and Speaker Volume Audio Tones Base onlyMuting the Ringer Do Not Disturb DNDTemporarily Muting the Ringer Tone Dialing SWITCH-OVER Mute MicrophoneTraveling OUT Range Booster Handset OnlyJoining a Conference Call Privacy ModeConferencing From a second handset Find HandsetSpeed Dialing Phonebook PhonebookIf you make a mistake while entering a name Store/Edit No. appears Storing Caller ID Messages in the Phonebook Storing a Redial RecordDeleting a Redial Record Viewing the PhonebookMaking Calls Using the Phonebook From Standby Mode Deleting ALL Phonebook Locations Base only From the handset Copying Phonebook LocationsTesting Stored Emergency Number From the baseCaller ID and Cidcw Caller ID on Call Waiting Incomplete DataCall Waiting Deluxe Features Viewing the Caller ID List Deleting Information from the Caller ID List Deleting ALL Caller ID NAME/NUMBERSCalling a Party from the Caller ID List From Standby ModeFrom Talk mode Register the Handset to the Base Expanding Your PhoneFour Multi-Handset Expandability Using the Directlink Mode DirectLink callINTERCOM/CALL Transfer Feature IntercomFOUR-WAY Conferencing Making an Intercom From a handsetCall Transfer Feature Answering an IntercomAnswering a Call Transfer To answer a page from a handsetAccepting the call transfer To answer a page from the baseFeatures Integrated Answering DeviceSelecting Your Greeting Base only Answering System SetupRecord a Personal Outgoing Message Base Only Setting a PIN Code Setting the Ring TimeSetting the Record Time Setting the Message Alert On or OffSetting the Language of your Answering System Setting the Call ScreenTurning the message alert tone off by pressing any key Turning the message alert tone off from a remote locationUsing Your Answering System Turning the Answering System ON/OFFRepeating a message New Message LEDPlaying your messages Skipping a message Deleting a message Voice memo Recording a conversationRemote access away from home Remote OperationFunction AnsweringMachine operation appears on the base Remote access with the handsetRemote Key Function Integrated Answering Device Troubleshooting Symptom SuggestionKeep the handset away from microwave ovens Service and Repair CareMemo RadioShack Corporation