VTech DS6221-4, DS221-2, DS221-3, DS6221-5, DS6222-4, DS6222-5 FCC, Acta and IC regulations, FCC Part

Page 55

Appendix

FCC, ACTA and IC regulations

FCC Part 15

This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this telephone.

To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The handset may be safely held against the ear of the user. The telephone base shall be installed and used such that parts of the user’s body other than the hands are maintained at a distance of approximately 20 cm (8 inches) or more.

This Class B digital apparatus complies with Canadian ICES-003.

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX.

This identifier must be provided to your local telephone company upon request.

The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines. See Installation Instructions in the user’s manual.

The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact your local telephone company.

This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected to your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.

If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents. For repair procedures, follow the instructions outlined under the Limited Warranty.

51

Page 54 Page 56
Image 55
Page 54 Page 56
Contents User’s manual Congratulations Table of contents Index AppendixGetting started Parts checklistTelephone base and charger installation Place in Charger Battery installation and chargingTabletop to wall mount installation Installation optionsSee Telephone base and charger installation on Wall mount to tabletop installationCharge light Handset layoutDelete Telephone base layoutKey tone Telephone settingsRinger volume handset Ringer toneSet date/time LCD languageHome area code Clear voicemailRemote code Answering system settingsAnswering system set up Number of ringsDelete your announcement AnnouncementPlay your announcement Record your own announcementTelephone operation Find handset MuteRinger mute Call waitingTo access a number in the call log while on a call To access a number in the directory while on a callChain dialing Handset 11, and *2 for Handset Multiple handset useIntercom Answer an incoming call during an intercom callScreen shows Calling Other HANDSET. Share an outside callShows Handset X is Calling Directory Shows Enter Name Store a directory entryNumber Character chartAlphabetical search Search the directoryDial a directory entry Delete from the directory Edit a directory entryShows Edit Number About caller ID Call log Missed calls indicatorMake a call log entry ready to dial Review the call logSave a call log entry to the directory Dial a call log entryDelete from the call log Delete from redial Call log display screen messagesRedial list Dial a redial entryAnswering system and voicemail Answering system operationMessage capacity Call intercept Telephone base ringer volumeTurn the answering system on or off Call screeningTo play messages with a handset New message indicationMessage playback To play messages with the telephone baseTo delete all messages with the telephone base Delete all messagesRecord and play memos Record a memoWindow display Description Message window displaysCommand Remote accessHandset display screen messages AppendixThere is no telephone line connected Handset icons Handset and telephone base indicators Handset lightsBattery indicator Telephone base lightsBattery Add and register a handset optional Expand your telephone systemReplace a handset Low Battery shows on screen TroubleshootingMy telephone does not work at all Charge light is off Telephone does not ring when there is an incoming callThere is no dial tone My handset beeps and is not performing normally Cannot dial outMy caller ID features are not working properly Hear other calls when using the telephoneHear noise on the cordless handset and the keys do not work Caller ID entries do not match the numbers I need to dial CONNECTING... shows in the handset screenOutgoing announcement is not clear Messages on the answering system are incomplete Answering system does not respond to remote commandsMessages on the answering system are very difficult to hear Answering system does not record messagesImportant safety instructions Operating range MaintenanceRbrc seal About cordless telephonesWhat does this limited warranty cover? WarrantyHow do you get warranty service? FCC Part FCC, Acta and IC regulationsIndustry Canada Technical specifications Index Index 91-002292-020-100
Top Page Image Contents