AT&T EP5995 user manual Remote access

Page 67

1. Dial your telephone number from any touch tone phone.

2. When system answers, enter

4-digit Remote Access Code (5000 unless it has been changed).

3. Enter remote commands (see list at right).

4. Hang up to end call and save all undeleted messages.

NOTE: If the answering sys- tem is turned off or if the memory is full, the system will pick up the next incoming call after 10 rings and ask for the remote access code. If the correct code is not entered after 3 tries, the call will be disconnected.

NOTE: If you pause for more than five seconds during remote access, you will hear a voice prompt to press 5 for help. The system will repeat this mes- sage every five seconds. After it announces it for the third time and no valid command is issued, the call will disconnect.

NOTE: Pressing # when listening to messages will stop the playback process and all unre- viewed messages will continue to be classified as new.

NOTE: Disconnecting the line during message without pressing # playback will cause all unreviewed messages to be classified as old.

Answering System Operation

Remote access

A four-digit security code is required to access your answering system from any touch tone phone. This code is 5000 by default; see page 56 to change it. The system will wait up to 10 sec- onds for each digit entry.

If you reach the system via remote access, enter the four-digit remote access code when the outgo- ing message is playing.

After hearing a double beep, enter one of the fol- lowing commands.

Commands in remote standby mode:

Hang up Saves all messages

1Plays all messages

2Plays new messages only

3 Deletes all messages

5 Announces next set of menu com- mands

7 Records new announcement

0 Turns answering system on or off

Commands during playback mode:

3Deletes the message currently playing and announces "Message deleted"

4Repeats the message currently playing

5 Pauses the message currently playing and announces "Message paused". If message is paused, it will resume play back.

6 Skips to the next message

# Stops message playback and announces For "help, press 5"

62

Image 67

Contents GHz Cordless Telephone/Speakerphone Answering System EP5995 Need HELP? Information about Caller ID with Call Waiting Stop Add new handsets to make your telephone more versatile see Table of Contents Handset Quick reference guideMain menu Telephone base Parts checklist Telephone operating range If you move out of range with- out pressing /OFF/CANCEL,Before you begin About caller identification CIDTelephone base installation Battery installation & charging Wall mounting Belt clip & optional headset Install belt clip as shown below if desiredHandset screen images Record ringer Ringer volumeHandset sounds Ringer melodyKeypad tone Messages Handset messagesSet time Handset settingsEdit handset name Language Show handset nameClear voicemail ContrastDefault settings Setting date and time Base settingsBase Settings Ringer Melody Base Settings Keypad Tone Language Press SELECT/MENU to confirm, or press CAN- CEL to abort Mute Basic handset operationMaking, answering and ending calls Hands-free speakerphone callsHold New voicemail light Basic base operationLast number redial Use lightIntercom HOLD/PAUSE Ringer silencing Volume controlOptions while on calls Call WaitingIntercom calls Intercom callsHandling incoming calls Memory capacity Timeouts and error tonesEntering a name New directory entriesCustomizing entries Entering a numberCalling a displayed number Directory searchBrowsing through the directory Searching alphabeticallyEditing a listing Editing or deleting an entryDeleting all entries Deleting an entryBase directory Base Directory Enter number, then press MENU/SELECT to confirm Use DIR or Vcid to search for the desired entry Editing a number Editing a nameEntry saved to Directory Clear redial How Caller ID worksClear call log Review redialReviewing your call log Reviewing your call logMissed Calls Saving or deleting an entry Returning a callPlayback options Dialing a call log entryDialing options Dialing an entry Reviewing your redial logAbout the redial log Reviewing your redial logDeleting an entry Reviewing voice messages Reviewing redial log Call logBase Call Log & Redial Options Dialing a call log entry Dialing a number from the redial log About the redial memoryRedial Options Message capacity Handset accessActivating the answering system Setting number of rings Setting answering systemSetting message alert tone Setting remote access code Setting call screening Deleting your announcement Outgoing announcementsRecording your announcement Playing your announcement Deleting all messages Message playback Announcements Options during playbackRecording a memo Recording and playing memosPlaying back a memo Message window displays Message window displaysRemote access Handset status icons Display screen status iconsBase status icons Indicator lights Alert tones and indicator lightsAlert tones Adding new handsets De-registering a handset Replacing a handsetDe-registering all handsets Re-registering a handset Charging spare battery pack My telephone does not work at all TroubleshootingThere is no dial tone Cannot dial out Hear noise Answer Common cure for electronic equipment Important safety information Especially about cordless telephones Especially about telephones answering systems Precautions for users of implanted cardiac pacemakersFCC Part 68 and Acta FCC Part 68 and Acta FCC Part Limited warranty Limited warranty Please retain your receipt as your proof of purchase Index Names Technical specifications Action Remote command Remote access wallet card