AT&T System 25 manual Account Code Entry Outgoing Calls, Account Code Entry Incoming Calls

Page 45

Standard Multiline Features

Account Code Entry	✓
	❑

For bookkeeping purposes, account codes may be assigned to use with certain calls. If you are required to use account codes for outgoing calls, the code must be entered before you can place an outgoing call.

See your System Administrator to verify the types of calls, if any, for which you must enter an account code.

Account Code Entry - Outgoing Calls

1Listen for dial tone, then press ❑* ❑0 .

2Dial the account code.

NOTE: If you make a mistake while entering the account code, press ❑* ❑0 again, then the correct account code.

3Listen for dial tone.

4Dial the outside line access code and listen for dial tone.

5Dial the telephone number.

NOTE: You cannot use the ACCT ENTRY button for this procedure.

Account Code Entry - Incoming Calls

1 After completing your conversation, and before you hang up,

press ACCT ENTRY .

(Continued)

41

Image 45

Contents AT&T To Order Copies of this Document Refer to Document Number Contents Glossary Introduction FeaturesConsole Buttons Attendant ConsolesLoop Buttons Automatic Loop SelectionSelector Console Handset Tones Using the Selector ConsoleLights Ringing TonesPersonal Dial Code PDC Data Dial Code DDCDisplay Unit Queue StatusAdditional Information This GuidePage Answering Calls Answering a CallDisplay Tango,S Attendant Message Waiting Turning on Message Waiting LightsTurning Off Message Waiting Lights Attendant Message Waiting Conference Calls Setting Up a ConferenceDunn,B Directory Using the DirectoryExample of a Directory Search Exiting from the Directory Placing Directory CallsViewing Display Screens DisplayDisplay symbol Meaning of the symbol Symbols Used in DisplaysThis is a Third-Party Data feature Setting the Clock, Date, or Alarm Using the TimerDisplay Functions Hold Automatic Hold and Automatic ReleasePlacing Calls on HoId Using Hold to Place Another Call Using Hold to Answer Another CallReturning to the Held Call Branch Incoming Calls Answering CallsExtending Calls Switching Between Parties Conference Using Inspect InspectDeactivating Inspect Acct Entry Activating Night Service Night ServicePaging Using the Paging SystemPark Parking a Call on the SlacParking Calls on the Selector Console Picking Up Parked Calls Placing Calls Placing Inside CallsPlacing Outside Calls For Someone Else 912125551212 Position Busy Using the Position Busy FeatureSystem Alarm Testing Your Console Testing the SlacTesting the Selector Console Page Account Code Entry Account Code Entry Outgoing CallsAccount Code Entry Incoming Calls ACCT? Automatic Intercom Using Auto IcomBilling Calls to Your Extension Call AccountabilityCall Waiting Callback Canceling CallbackRequesting Callback Completing CallbackQueue Denied Blake,G s CoveragePlacing a Data Call Data Calls Placed from Your TelephoneDirect Group Calling DGC Leaving the GroupReturning to the Group Placing Calls Direct Station Selection DSSActivating Exclusion ExclusionFollowing SigningSigning Out Signing Out All Extensions Canceling Forwarding ForwardingForwarding Calls Ending Calls Hands-Free AnsweringLast Number Dialed Using Last Number DialedLeaving Messages When Not on a Call Leave Word CallingLeaving Messages While on a Call Message Waiting Turning On Message LightsTurning Off Message Lights Sending a Personal Signal Canceling a Personal SignalPersonaI Message Waiting Pickup Picking Up CallsPicking Up Calls in Your Pickup Group Special Characters Programming NumbersProgramming Buttons Personal Speed Dialing Codes Using # as a CharacterProgramming or Removing Numbers Recall Repertory Dialing REP Dial Signaling Another Telephone SignalingPress the Speakerphone button and listen for dial tone SpeakerphoneWait until you have completed your conversation Speed Dialing Transferring Calls TransferPage Glossary DDC Fpdc PDC Slac Switchhook AT&T System Switched Loop Attendant ConsoleSee Features list on other side Graphics AT&T

Related manuals

Manual 14 pages 61.58 Kb