DKS Enterprises 1803, 1808, 1802 System Administrator, Remote Programming, Remote Relay Activation

Page 44

5.2 SYSTEM ADMINISTRATOR

The administrator can perform the following operations from a remote location using a touch-tone telephone. You must know the phone number of the system and the system master code.

5.2.1 Remote Programming

1.Call the telephone number that the entry system is installed on. The system will answer with a short tone (beep). Note: the number of rings before the system answers is dependent on the programming in 3.1.8.

2.After the system answers, follow the desired programming steps in Section 3.

3.When complete, hang up. You cannot use 0# together to end the programming step from a touch-tone telephone.

5.2.2 Remote Relay Activation

1.Call the telephone number that the entry system is installed on. The system will answer with a short tone (beep). Note: the number of rings before the system answers is dependent on the programming in 3.1.8.

2.Press and enter the four-digit MASTER CODE BBBB(beep).

3.Press the desired tone open number B(beep). NOTE: Refer to 3.1.5 to determine which tone open features have been programmed, i.e. momentary open, hold open, release, hold open one hour and then release.

4.Hang up.

5.2.3 Relay Check

The telephone entry system can be called and a check can be made to determine if any of the relays in the system are in a "hold open" mode. This check can be useful if yourr gate (or door) is held open and you suspect that the telephone entry system relay may be the cause.

1.Call the telephone number that the entry system is installed on. The system will answer with a short tone (beep). Note: the number of rings before the system answers is dependent on the programming in 3.1.8.

2.Press and enter the four-digit MASTER CODE BBBB(beep).

3.The system will emit a series of short tones if the relay is in a continuous activation mode.

Relay 1 activated:	beep - pause - beep - pause . . .
Relay 2 activated:	beep beep - pause - beep beep - pause . . .
Relay 1 & 2 activated:	beep beep beep - pause - beep beep beep - pause . . .

4.Press the programmed tone number Bto deactivate the relay (beep). The system will automatically hang up.

44

Image 44

Contents 1802, 1803, 1808, 1810 Telephone Entry Systems Page Use this manual with the following models only Table of Contents Maintenance and Trouble Shooting Important Notice ListingGeneral Information Features Installation Installation Guidelines ALL SystemsSurface Mount 1803 and 1810 Units Surface Mount 1803 and 1810 Units with Recess Box Flush Mount 1803 and 1810 Units Flush Mount Rough-in Box applies to 1803 and 1810 only Flush Mount Trim Ring use with 1803 and 1810 units only 12.0 375 125 DIA 125 SQ 625 7 1802 Surface Mount Only 8 1808 Surface Mount Only Memory Chip Installation Postal Lock Installation Page Wiring 18AWG Main Terminal Description Terminal DescriptionWiring Description Relay Wiring Typical Controlling a Single Door or GateControlling a Gate Operator and Pedestrian Gate or Door Programming Notes Programming from the KeypadProgramming from an Offsite Location General Programming Master CodeSingle or Multiple Systems Relay Strike TimeTalk Time Tone Open NumbersNumber of Rings to Answer Postal SwitchTouch-tone / Rotary-dial Keypad Function Star * Key FunctionProgramming 7-digit Phone Numbers Phone Number ProgrammingProgramming the Directory Code Length Deleting Individual Phone Numbers Programming Area CodesProgramming Phone Numbers with Area Code Reference Display Phone Numbers with known Directory Codes Delete All Phone NumbersDisplay / Delete Phone Numbers Entry Code Programming Four-Digit Entry Code ProgrammingDelete Four-Digit Entry Codes Delete All Four-Digit Entry CodesFive-Digit Entry Code Programming Delete Five-Digit Entry CodesDelete All Five-Digit Entry Codes Five-Digit Entry Code Divide NumberAutomatic Relay Activation Time Zones Time Functions ProgrammingTime Clock Programming Four-Digit Entry Code Time Zone Five-Digit Entry Code Time ZoneFlash Entry Codes Relay 2 Terminals Speaker Volume FeedbackClick Sensitivity Display Contrast 1802, 1803, 1810 onlyHandset / Hands Free Master Code SwitchRing Pin Using an Entry Code General InstructionsGuest Instructions Responding to a Guest CallSystem Administrator Remote ProgrammingRemote Relay Activation Relay CheckEntry Code Time Zone Enable / Disable Auto Relay Time Zone Enable / DisableLine Sharing Switch Input OperationMiscellaneous Operating Instructions Connection to a PBX Areas with 10-digit DialingPage Maintenance Trouble ShootingSympton Possible Solutions Accessories LOG Tables Name Phone Number Directory Code Entry Alternate Area Code Name Phone Number Directory Code Entry Alternate Area Code Resident Instruction Sheet