DKS Enterprises 1802, 1803, 1808, 1810 owner manual Important Notice, Listing

Page 6

IMPORTANT NOTICE

FCC - UNITED STATES

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules and Regulations. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Registration Number: DUF6VT-12874-OT-T

DOC - CANADA

The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The Department does not guarantee the equipment will operate to the users satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable means of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure, for their own protection, that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

DOC Registration Number: 1736 4528 A

Notice:

The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the sum of the load numbers of all the devices does not exceed 100.

Notice:

DoorKing does not provide a power transformer on units sold into Canada. Use only transformers that are CSA listed to power the telephone entry system. 1802, 1803, 1808, 1810, 1814, 1815, 1818 and all "P" series systems require a 16.5-volt, 20 VA transformer. The models 1816 and 1817 require a 16.5-volt, 40 VA transformer. The model 1812 requires a 24-volt, 20 VA transformer.

Listing:

This product has been tested to and found to be in compliance with the U.L 294 Safety Standard by Intertek Testing Services NA Inc. (a Nationally Recognized Testing Laboratory) and is ETL listed.

6

Image 6
Contents 1802, 1803, 1808, 1810 Telephone Entry Systems Page Use this manual with the following models only Table of Contents Maintenance and Trouble Shooting Important Notice ListingGeneral Information Features Installation Installation Guidelines ALL SystemsSurface Mount 1803 and 1810 Units Surface Mount 1803 and 1810 Units with Recess Box Flush Mount 1803 and 1810 Units Flush Mount Rough-in Box applies to 1803 and 1810 only Flush Mount Trim Ring use with 1803 and 1810 units only 12.0 375 125 DIA 125 SQ 625 7 1802 Surface Mount Only 8 1808 Surface Mount Only Memory Chip Installation Postal Lock Installation Page Wiring 18AWG Main Terminal Description Terminal DescriptionWiring Description Relay Wiring Typical Controlling a Single Door or GateControlling a Gate Operator and Pedestrian Gate or Door Programming from the Keypad Programming from an Offsite LocationProgramming Notes Single or Multiple Systems General ProgrammingMaster Code Relay Strike TimeTalk Time Tone Open NumbersPostal Switch Touch-tone / Rotary-dialNumber of Rings to Answer Keypad Function Star * Key FunctionPhone Number Programming Programming the Directory Code LengthProgramming 7-digit Phone Numbers Programming Area Codes Programming Phone Numbers with Area Code ReferenceDeleting Individual Phone Numbers Delete All Phone Numbers Display / Delete Phone NumbersDisplay Phone Numbers with known Directory Codes Delete Four-Digit Entry Codes Entry Code ProgrammingFour-Digit Entry Code Programming Delete All Four-Digit Entry CodesDelete All Five-Digit Entry Codes Five-Digit Entry Code ProgrammingDelete Five-Digit Entry Codes Five-Digit Entry Code Divide NumberTime Functions Programming Time Clock ProgrammingAutomatic Relay Activation Time Zones Four-Digit Entry Code Time Zone Five-Digit Entry Code Time ZoneFlash Entry Codes Relay 2 Terminals Click Sensitivity Speaker VolumeFeedback Display Contrast 1802, 1803, 1810 onlyMaster Code Switch Ring PinHandset / Hands Free Guest Instructions Using an Entry CodeGeneral Instructions Responding to a Guest CallRemote Relay Activation System AdministratorRemote Programming Relay CheckEntry Code Time Zone Enable / Disable Auto Relay Time Zone Enable / DisableSwitch Input Operation Miscellaneous Operating InstructionsLine Sharing Connection to a PBX Areas with 10-digit DialingPage Maintenance Trouble ShootingSympton Possible Solutions Accessories LOG Tables Name Phone Number Directory Code Entry Alternate Area Code Name Phone Number Directory Code Entry Alternate Area Code Resident Instruction Sheet