Panasonic KX-TCD705BX operating instructions Before Requesting Help, Problem Cause and Remedy

Page 49

KX-TCD705BX 12/7/01 2:28 pm Page 49

Before Requesting Help		➡
Problem	Cause and Remedy

“Î” flashes and an alarm tone sounds when you ZOor %.

•You are too far from the base unit. Move closer and

•try again.

•Plug in the AC adaptor.

•The handset has been cancelled or has not been registered. Register the handset in the base unit (page 41).

•If the handset is registered to more than one base unit, check ‘selecting the base unit access’ (page 42).

A busy tone sounds when you ZOor %.

•Another handset is in use.

“Î” flashes during a conversation	• The handset is out of range. Move closer to the
and the call is disconnected.	• base unit and make the call again.
	• Plug in the AC adaptor.

The unit does not work.

•Turn the power ON (page 12).

•Check the settings.

•Charge the batteries fully (page 7).

•Clean the charge contacts and charge again (page 7).

•Unplug the AC adaptor and turn the power OFF to reset. Plug in the AC adaptor and turn the power ON. Then try again.

•Re-install the handset batteries (page 7) and try again.

•The handset has been cancelled or has not been registered. Register the handset (pages 39, 41).

You cannot dial.	• Check that the dialling mode selection is correct (page 44).
	• The dialled number is restricted. Cancel the number
	(page 45).
	• Key lock mode is set. Cancel the mode (page 36).

Static, sound cuts in/out, fades.	• Locate the handset and base unit away from other
Interference from other electrical	• electrical appliances.
units.	• Move closer to the base unit.

The handset does not operate or ring.

•Turn the power ON (page 12).

•The ringer is set to OFF. Select the desired volume level (page 37).

The base unit does not ring.

•The ringer is set to OFF. Select the desired volume level (page 44).

49

Image 49

Contents Operating Instructions Dear purchaser Battery Cover Belt Clip Operating InstructionsSafety Instructions Contents Chapter Programmable Functions On the Base Unit Using an Optional HeadsetConnections Getting StartedBattery Charge Installing the Batteries in the HandsetBattery Strength Battery InformationBattery Replacement Battery CautionGetting Started Base Unit LocationWall Mounting Base Unit Location of ControlsHandset Displays Basic Start-up Operations To Dial after Confirming the Entered Number Making CallsHandset Digital Speakerphone To Redial the Last Number Dialled Making CallsTo Redial after Confirming the Numbers in Redial Memory To Edit/Clear Numbers in the Redial ListDuring conversation, ZSor Uto select level Auto RedialHot Key Dialling Direct CallDialling a Number from the Phonebook or Caller ID List Auto Talk Answering CallsTo Turn the Handset Ringer Off Temporarily During incoming call, Zand hold UPrivate category feature Using the PhonebookNames up ZYor Storing Names and Numbers in the PhonebookSelect ‘Save’ To change the character mode Using the PhonebookTo Enter Names Selecting Characters If you make a mistake while entering a Name/NumberY Y Z Z Z Z Dialling from the Phonebook Finding Items in the PhonebookClearing an Item from the Phonebook Editing an Item in the PhonebookHandset 1 Sender Handset 2 Receiver Phonebook CopyHandset 1 Sender ZU or Sto select Name/Number in the Phonebook to copyHandset 2 Receiver Follow steps 1-4 on Handset 2 on ZUto select ‘Copy Forward’Dialling a Stored Number Storing Phonebook Items as Hot Key DialsSelect ‘Clear’ Clearing an Item in the Hot Key DialHow Caller Information is Displayed when a Call is Received Caller ID ServiceChecking the Number of New Calls Incoming CallWhen viewing long telephone numbers Using the Caller ListViewing the Caller List What ‘’ meansCalling Back from the Caller List Using the Caller ListEditing the Caller’s Name / Number Clearing the Caller ListZU or Sto select ‘All Clear’ Storing the Caller List Information in the PhonebookEnter name if required, up to 16 characters pages 20 Paging All Handsets from the Base Unit Paging/IntercomIntercom between Handsets Transferring a Call from One Handset to AnotherConference Transferring a Call using the IntercomTransferring a Call without the Intercom Operating More than One Handset For Optional Multi-Unit UsersOperating More than One Base Unit Selecting the Display LanguageHow to Use the Pause Feature Special FeaturesUsing the Recall Feature Setting the Key Lock on Special FeaturesTo Cancel the Key Lock Temporary Tone DiallingStandby Mode To Change the Initial SettingsHandset Programming While programmingHandset Programming Main Item Sub Menu DescriptionSetting*1Main Item Sub Menu Description Setting Setting Direct Call Number Setting Time AlarmRegistering a Handset to a Base Unit Setting the Handset PINSelect Base Unit Cancelling a Base UnitBell Selection Base ProgrammingSelect the Dialling Mode Select the Base Unit Ringer VolumeBase Programming Set Base Unit PINSelect Pause Timing Select Earth/Flash ModeSetting the Clock Cancelling a HandsetSetting the Date Reset Base UnitUsing the Belt Clip Using an Optional HeadsetConnecting the headset to the handset To adjust the headset receiver volume HIGH, Medium or LOWOption Covers Before Requesting Help Problem Cause and RemedyLong, the number will not be redialled correctly Adding Another Phone QUQX00004ZA KU0701NMH0 Model No. KX-TCD705BX