Panasonic KX-TCD705BX operating instructions Adding Another Phone

Page 51

KX-TCD705BX 12/7/01 2:28 pm Page 51

Problem

Cause and Remedy

You cannot register the handset in the base unit.

•The base unit has registered a maximum of 6

•handsets or the handset has registered a maximum of 4 base units.

•A wrong base unit PIN was entered. Enter the correct PIN.

•There is interference from other electrical units, locate the handset and base unit away from them.

•You must finish registration within 1 minute after the ringer tone sounds, or programming will be cancelled (page 41).

The battery strength is not	• Make sure the Panasonic P-6P or BYD
displayed correctly.	• N4DH33B00001 is installed (page 7).
	• Check that the battery type selection is correct (page
	39).

“Û” flashes or the unit bleeps every 15 seconds.

•Charge the batteries fully (page 7).

You charged the batteries fully, but “Û” flashes.

•Clean the charge contacts and charge again (page 7).

•Install new batteries (page 7).

Adding Another Phone

This unit will not function during a power failure. To connect a standard telephone on the same line, use a T-adaptor.

To Telephone Socket

T-Adaptor

Telephone Line Cord

Standard Telephone

51

Image 51

Contents Operating Instructions Dear purchaser Battery Cover Belt Clip Operating InstructionsSafety Instructions Contents Chapter Programmable Functions On the Base Unit Using an Optional HeadsetConnections Getting StartedBattery Information Installing the Batteries in the HandsetBattery Charge Battery StrengthBase Unit Location Battery CautionBattery Replacement Getting StartedWall Mounting Location of Controls Base UnitHandset Displays Basic Start-up Operations Making Calls To Dial after Confirming the Entered NumberHandset Digital Speakerphone To Edit/Clear Numbers in the Redial List Making CallsTo Redial the Last Number Dialled To Redial after Confirming the Numbers in Redial MemoryDuring conversation, ZSor Uto select level Auto RedialDirect Call Hot Key DiallingDialling a Number from the Phonebook or Caller ID List During incoming call, Zand hold U Answering CallsAuto Talk To Turn the Handset Ringer Off TemporarilyUsing the Phonebook Private category featureNames up Storing Names and Numbers in the Phonebook ZYorSelect ‘Save’ If you make a mistake while entering a Name/Number Using the PhonebookTo change the character mode To Enter Names Selecting CharactersY Y Z Z Z Z Dialling from the Phonebook Finding Items in the PhonebookClearing an Item from the Phonebook Editing an Item in the PhonebookZU or Sto select Name/Number in the Phonebook to copy Phonebook CopyHandset 1 Sender Handset 2 Receiver Handset 1 SenderHandset 2 Receiver Follow steps 1-4 on Handset 2 on ZUto select ‘Copy Forward’Dialling a Stored Number Storing Phonebook Items as Hot Key DialsSelect ‘Clear’ Clearing an Item in the Hot Key DialIncoming Call Caller ID ServiceHow Caller Information is Displayed when a Call is Received Checking the Number of New CallsWhat ‘’ means Using the Caller ListWhen viewing long telephone numbers Viewing the Caller ListClearing the Caller List Using the Caller ListCalling Back from the Caller List Editing the Caller’s Name / NumberStoring the Caller List Information in the Phonebook ZU or Sto select ‘All Clear’Enter name if required, up to 16 characters pages 20 Transferring a Call from One Handset to Another Paging/IntercomPaging All Handsets from the Base Unit Intercom between HandsetsTransferring a Call using the Intercom ConferenceTransferring a Call without the Intercom Selecting the Display Language For Optional Multi-Unit UsersOperating More than One Handset Operating More than One Base UnitSpecial Features How to Use the Pause FeatureUsing the Recall Feature Temporary Tone Dialling Special FeaturesSetting the Key Lock on To Cancel the Key LockWhile programming To Change the Initial SettingsStandby Mode Handset ProgrammingHandset Programming Main Item Sub Menu DescriptionSetting*1Main Item Sub Menu Description Setting Setting Direct Call Number Setting Time AlarmRegistering a Handset to a Base Unit Setting the Handset PINSelect Base Unit Cancelling a Base UnitBell Selection Base ProgrammingSet Base Unit PIN Select the Base Unit Ringer VolumeSelect the Dialling Mode Base ProgrammingSelect Pause Timing Select Earth/Flash ModeReset Base Unit Cancelling a HandsetSetting the Clock Setting the DateTo adjust the headset receiver volume HIGH, Medium or LOW Using an Optional HeadsetUsing the Belt Clip Connecting the headset to the handsetOption Covers Before Requesting Help Problem Cause and RemedyLong, the number will not be redialled correctly Adding Another Phone QUQX00004ZA KU0701NMH0 Model No. KX-TCD705BX