Panasonic KX-TG7841UE, KX-TG7841BX Error messages, Display message, Cause/solution

Page 59

Useful Information

Error messages

Display message

Base no power

or

No link. Re-connect base AC adaptor.

or

No link.

Busy

Call phone company for your access #

Check tel line

Error!!

Failed

Invalid

Requires subscription to Caller ID.

Cause/solution

RThe handset has lost communication with the base unit. Move closer to the base unit and try again.

RUnplug the base unit’s AC adaptor to reset the unit. Reconnect the adaptor and try again.

RThe handset’s registration may have been canceled. Re-register the handset (page 66).

RWhen “No link.” is displayed during a power failure, place a handset on the base unit to supply power to the base unit.

RNo cellular phone is paired to the base unit. Pair a cellular phone (page 14).

RThe called unit is in use.

ROther unit is in use and the system is busy. Try again later.

RThe handset you are using is too far from the base unit. Move closer and try again.

RYou have not stored the voice mail access number. Store the number (page 55).

RThe supplied telephone line cord has not been connected yet or not connected properly. Check the connections (page 8).

RIf you do not connect the telephone line cord and use only cellular lines, set the cellular line only mode (page 16).

RRecording was too short. Try again.

RSomeone is using a cellular line or headset. Try again later.

RThe phonebook copy is incomplete (page 45). The cellular phone is disconnected from the base unit. Make sure that other Bluetooth devices are not connected to the cellular phone, and try again.

RAlthough the unit tried to connect to the cellular phone or headset, the connection has been failed.

–Someone is using a cellular line or headset. Try again later.

–Make sure that the cellular phone or headset is not connected to other Bluetooth devices.

RThe handset is not registered to the base unit. Register the handset (page 66).

RYou must subscribe to a Caller ID service. Once you receive caller information after subscribing to a Caller ID service, this message will not be displayed.

59

TG7841BX_UE(en)_0528_ver011.pdf 59

2013/05/28 18:56:50

Image 59

Contents Thank you for purchasing a Panasonic product KX-TG7841UETable of Contents Additional/replacement accessories Accessory informationSupplied accessories Trademarks Bluetooth devicesYour Bluetooth cellular phone*1 2 max Your Bluetooth headset*1 1 maxFor your safety Base unit location/avoiding noise Important safety instructionsBattery For best performanceRoutine care SpecificationsOther information Connections Setting upBattery installation Battery chargingOperation Operating time Intelligent eco modeBattery level Icon Battery levelMholdn ControlsMoffn Mflashnmcall Waitn Mnoise Reductionn Handset display items Display/IndicatorsBelt clip Base unit display items Cell 1/CELL 2 indicators on the base unitDate and time Initial settingsDialing mode Moffn Link to cell featurePairing a cellular phone Unpairing a cellular phoneAuto connection to the cellular phone Link to cell settingsRing as cell mode Selecting which unit receives cellular callsWhen you use the landline again Cellular line only mode If you do not use the landlineConnecting/disconnecting the cellular phone manually Msaven a Mexitn Changing the Bluetooth PIN Personal Identification NumberCellular line selection Storing your area code for a local callMaking landline calls Making cellular callsHold Useful features during a callAnswering calls For call waiting or Call Waiting Caller ID service usersHandset noise reduction Flash for landline callsMbN Transfer to cell a Using the other line during a conversationCall share To hold the 2nd call Mmenun a MbN Hold a Mselectn Power back-up operation for landlineMaking calls during a power failure Making a call using the redial list Answering calls during a power failureMexitn Adjusting the speaker volumeMaking a cellular call using the redial list MredialnWhile the base unit is ringing for an incoming call For call waiting or Call Waiting Caller ID service usersMZN To switch between calls, press Mcall WaitnKey Character GroupsCharacter table for entering names Erasing the character or numberMokn Searching by first characterSearching by query Searching by groupErasing an entry Editing entriesErasing entries Chain dialSpeed dial Main menu Answering device Programmable settingsDisplay menu tree and direct command code table HandsetGreeting Record greeting Settings Ring count RingsPlay all msg Erase all msgAdd new Disconnect BluetoothDevice *3 Ringer volume Link to cell ConnectTime adjustment*9 Caller ID auto Settings Auto connect MinMode Cell line select Cellphone 1*3 Alarm OnceSet date & time Date and time Time adjustment *9 Caller ID autoVoice mail *2 Store VM access# Set tel line *2 Set dial mode PulseBase unit Start/End Talking CID *6 On Off Main menu Initial settingNight mode On Off Interrupt tone *6, *10 On OffSpecial programming AlarmNight mode Turning night mode on/offMbN Call block a Mselectn MbN Yes a Mselectn Storing unwanted callersFrom the caller list Handset McidnArea Setting the first ring for the call block listBlocking incoming calls without phone number Viewing/editing/erasing call block numbersRinger ID for handset Using Caller ID serviceCaller ID features Talking Caller IDMbN Group a Mselectn Using a cellular line HandsetCaller list Viewing the caller list and calling backTo erase your area code Editing a caller’s phone number before calling backErasing selected caller information Mselectn Moffn Erasing all caller informationTo copy from other cellular phones not paired Setting conversion codesWhen Select mode menu is displayed Copying phonebook from a cellular phone phonebook transferUnpairing a headset Pairing a headset to the base unitOperating a Bluetooth wireless headset using a landline Connecting/disconnecting a headsetAnswering landline calls with your headset Switching between the base unit and your headsetAdjusting your headset receiver volume To switch to the base unit Press MZN on the base unitMemory capacity including your greeting message Answering system for landlineTurning the answering system on/off Greeting messageListening to messages using the base unit Editing the number before calling back Listening to messages using the handsetErasing all messages Operating the answering systemNew message alert by a call Alerting featuresAdvanced new message Audible message alertRemotely Remote access codeUsing the answering system Remote operationTurning on the answering system remotely Answering system settingsRemote commands Voice guidanceSelecting Greeting only Caller’s recording timeListening to voice mail messages Voice mail service for landlineStoring the voice mail VM access number To erase the voice mail access numberMaking an intercom call IntercomHandset locator Transferring calls, conference callsTo establish a conference call Press Mconfn Answering a transferred callMbN Stop conference a To complete the transfer Press MZNWall mounting Display message Error messagesCause/solution General use TroubleshootingUse rechargeable battery ProblemMaking/answering calls, intercom Battery rechargeCan make and answer cellular calls but cannot hear a sound Caller ID/Talking Caller ID Using Bluetooth devices Answering system Bluetooth PINDeregistering a handset Liquid damageRegistering a handset to the base unit Index For your future reference