Panasonic WX-CC412, WX-CC411 QqSetting Network Cameras connected to the unit Camera, Camera 1 to

Page 15

User authentication will be required when connecting to Network Cameras.

User authentication will not be required when connecting to Network Cameras.

Browser Operation

[Sender’s E-mail address]

Input the sender’s email address. The email address entered will appear in the “From” line on the email being sent. Number of characters: 3 to 128

Types of characters: alphanumeric, characters @ . _ ‑

Default setting: None (blank)

qqSetting Network Cameras connected to the unit [Camera]

This tab is used to set Network Cameras displayed on the LCD display of the Center Module. Setting Network Cameras enables camera images from vehicle detectors to be displayed on the Center Module in tandem with security alerts.

Click the [Installation] button, then the [Camera] tab.

Camera 1 to 4

A maximum of four Network Cameras can be connected to the Center Module. This section describes how to set Network Cameras connected to the unit.

Important

ppNetwork Cameras that can be connected to the Center Module are Panasonic i-pro series Network

Cameras.

ppBe sure to set HTTP for the Network Camera

connection method setting.

ppConfigure the Network Cameras to the following settings:

·Aspect ratio: 4:3

·Image quality: standard

[Delete] button

This button is used to restore the Network Camera settings to the default settings.

[IP address]

Input the IP address of the Network Cameras that are connected to the unit.

Default setting: None (blank)

[HTTP port]

Input the port number of the Network Cameras that are connected to the unit.

Settable port numbers: 1 to 65535

Default setting: 80

[Authentication]

Configure this setting if the user authentication setting is set to “ON”.

ON:

OFF:

[User name]

If [ON] is selected for [Authentication], input the username for accessing the Network Cameras.

Number of characters: 0 to 32

Default setting: None (blank)

[User password]

If [ON] is selected for [Authentication], input the password for accessing the Network Cameras.

Number of characters: 0 to 32

Default setting: None (blank)

15

Image 15

Contents Operating Instructions Browser Guide Contents WwPreface WwFeaturesWwSystem diagram Before useWwOperation Single laneDual lane Tandem lane WwConcerning the Operating InstructionsWwSystem requirements WwTrademarks and registered trademarksWwAbbreviations WwBrowser Compatibility Operating precautionsWwRouter WwBrowser Refresh RateQqDirect connection to the PC NetworkWwExamples of connections WwNetwork SecurityWwConnecting the Center Module via a PC WwSetup InstructionsBrowser Operation WwSetup Menu Setup menuWwOperation Screen NTP/ Time zone WwConfiguring and Confirming Settings at InstallationMaintenance QqConfirming the date and time setting Date & timeQqConfiguring network settings Network IPv4 NetworkWeb server UPnP QqConfiguring server settings ServerNTP server address Time adjustment interval timeAuthentication Pp Type Pp User passwordCamera 1 to QqSetting Network Cameras connected to the unit CameraQqSetting Help contact Help contact Configuring Help contact email transmission settingsQqSetting Site information Site info Level -20 to 0 dB WwConfirming store settingsQqConfirming nighttime volume settings Nighttime volume Nighttime volumeHoliday message QqConfirming store hours Store hoursStore hours Closed messageDevice for Line Input volumeOutput volume Aux speakerQqConfirming greeter message settings Greeter message WwConfirming message settingsSchedule list Message listQqConfirming reminder message settings Reminder message Pp GroupPp AUX Start Ending time IntervalInterval time Destination Pp Group QqConfirming alert message settings Alert messageList of alerts WwConfirming the security alert settingsRemaining capacity Mail for Alert * * 1 toWwConfirming quick operation settings WwBacking up settingsLane a setting Lane B setting WX‑CC412 only Pp Status WwPerforming maintenance on Center ModuleQqChecking the Center Module Status Pp Port numberMessage Meaning Action RebootLane column QqRetrieving log data LogDelete checkbox File columnQqConfirming the software version Update QqSetting authentication User mngUser ID change Confirm new password Password changeOld password New passwordQqChecking the status of security alerts Security alert WwChecking the status of All-In One Headsets and Belt PacksInformation display menu WwChecking the status of alertsQqChecking the status of system alerts System alert Troubleshooting Pp Has an SD card been inserted? Pp Is default gateway set for the network?Pp Is port forwarding set for the router? Center Module cannot beF0114-0 PGQP1741ZA