Sennheiser LV308 manual Indications, Operation and battery status indication, RF signal indication

Page 10

EK 1038 receiver

Indications

Alphanumeric display

4-step battery status display

Lock mode icon (lock mode is activated)

Operation and battery status indication

The red LED (LOW BAT/ON) provides information on the current operating state of the receiver:

Red LED lit up: The receiver is switched on and the capacity of the batteries/rechargeable battery BA 2015 is suffi- cient.

Red LED flashing:The batteries are/the rechargeable battery BA

2015 is going flat (LOW BAT)!

In addition, the 4-step battery status display on the display panel provides information on the remaining battery/rechargeable battery BA 2015 capacity:

3 segments:	capacity approx. 100 %
2 segments:	capacity approx. 70 %
1 segment:	capacity approx. 30 %

Battery icon flashing: LOW BAT

RF signal indication

The green LED (RF) at the front of the receiver lights up when an RF signal is being received.

However, the green LED (RF) does not light up when the audio out- put is muted because the RF signal of the received transmitter is too weak.

Display backlighting

After pressing a button, the display remains backlit for approx. 15 seconds.

10

Image 10

Contents Tourguide UHF Page Contents Thank you for choosing Sennheiser Important safety instructions Safety check Power sourceReplacement parts OverloadingSafety instructions for Lithium-Ion rechargeable batteries Do not solderTourguide UHF system System componentsEK 1038 receiver Special featuresOperating controls RF signal indication Operation and battery status indicationSegments Capacity approx % Battery icon flashing LOW BAT IndicationsConnecting the headphones Inserting and changing the battery pack/batteriesHow to properly use the battery pack or the batteries Preparing for useAdjusting the volume Using the receiverSwitching the receiver on/off Switching the channelOperating menu of the receiver Configure the receiverMenu is given within the chapter The setup menu Attaching the receiver to clothingStarting the setup menu Function of the buttons in the setup menuSelecting a menu Getting into the operating menu of the setup menuGetting into the setting mode of a menu Software stored on a chip in the deviceCanceling the entry Adjusting a settingStoring a setting Exiting the setup menuSetup menu of the receiver LOC. OFF LOC. onLocking channels for the user Adjustment tips for the setup menuActivating/deactivating the lock mode Changing the receiving frequencies of the channelsAdjusting the squelch threshold Releasing locked channelsDisplaying the revision of the firmware Limiting the volume at the headphone outputCopy function Slave Quick charger LED indications Cascading several chargers Setting up the chargerSwitching the charger on or off Do not place the receiver on delicate surfacesCharging the rechargeable battery BA Using the chargerCare and maintenance Compartments As shown Red LEDChannel bank system SK 100 G2 / SK 300 G2 / SK 500 G2Quick charger SKM 100 G2 / SKM 300 G2 / SKM 500 G2 radiomicrophones Delivery includesInserting and changing the battery Changing the microphone moduleUsing the radiomicrophone Switching the radiomicrophone on/offMuting the radiomicrophone SK 100 G2 / SK 300 G2 / SK 500 G2 bodypack transmitters Inserting and charging the accupack Use the microphone clips Connecting the microphone/line cableAttaching the microphones Positioning the microphonesMuting the transmitter Using the bodypack transmitterSwitching the transmitter on/off Play appears on the display panelSKP 100 G2 / SKP 500 G2 plug-on transmitters Microphone input, XLR-3 socket Button UP UnbalancedPlugging the transmitter onto the microphone Betriebs- und Batterieanzeige LC display panel LC display panel Evolution wireless transmitters GBattery status indication Mute displayPilot display Display backlightingOverview of menus ButtonsGetting into the operating menu Working with the operating menuExiting the operating menu Exit Overview of the operating menu of the transmittersDisply Adjusting the sensitivity Switching between channel banksSwitching between the channels in a channel bank Selecting the frequencies to be stored in the channelSwitching the phantom powering on/off SKP 500 G2 onlySelecting the standard display Loading the factory-preset default settingsEntering a name Activating/deactivating the pilot tone transmission Activating/deactivating the lock modeExiting the operating menu Set transmitter and receiver to TroubleshootingError checklist Deactivate the muting functionFor the radiomicrophones Recommendations and tipsFor the receiver EK …for the bodypack transmittersProgress you can hear HDX noise reductionInherent Accessories and spare parts Quick chargerSK 100 G2 / SK 300 G2 / SK 500 G2 bodypack transmitter SKP 100 G2 / SKP 500 G2 plug-on transmitterEK 1038 receiver Specifications2015charger Automatic security switch-off after 6 h at the latest Evolution wireless transmitters GDeep discharge recovery charge Plug-in mains unitsChannel assignment Tune ChanWarranty Manufacturer declarationsWeee Declaration Statements regarding FCC and industry CanadaManufacturer declarations