Sennheiser LV308, LV307 manual Adjusting a setting, Storing a setting, Canceling the entry

Page 16

Using the receiver

Adjusting a setting

Press the / (UP/DOWN) rocker button to adjust the setting of the menu.

The new setting flashes on the display.

By briefly pressing the rocker button, the display jumps either forwards or backwards to the next setting. In the “TUNE” menu, the rocker button features a “fast search” function: If you hold down the or button, the display cycles continuously, allow- ing you to get fast and easily to your desired setting. The new setting flashes on the display until it is stored.

Storing a setting

Press the SET button to store the setting. “STORED” appears on the display, indicating that the setting has been stored. You return to the operating menu of the setup menu. The last menu selected flashes on the display.

Canceling the entry

Press the ESC button to cancel the entry. With the menus “LOCK“, “SQUELCH“, “LTD“, “SW-REV“ and “COPY“ you return to the start display “SETUP“. The last menu remains unchanged.

An exception is the “TUNE“ menu. When canceling the entry with this menu, you will stay in the setting mode of the menu but you return to the display of the current channel (e.g. “CH 01“). It is then possible to restart your entry.

Exiting the setup menu

Switch the receiver off to exit the setup menu. To do so, turn the volume control counterclockwise until it clicks

If you then restart the receiver you get into the user menu and the current channel is displayed.

Operating menu of the receiver

The user menu of the receiver

USER-MENÜ

Kanal einstellen

/

: Kanal

01...20

16

Image 16

Contents Tourguide UHF Page Contents Thank you for choosing Sennheiser Important safety instructions Power source Replacement partsSafety check OverloadingSafety instructions for Lithium-Ion rechargeable batteries Do not solderTourguide UHF system System componentsEK 1038 receiver Special featuresOperating controls Operation and battery status indication Segments Capacity approx % Battery icon flashing LOW BATRF signal indication IndicationsInserting and changing the battery pack/batteries How to properly use the battery pack or the batteriesConnecting the headphones Preparing for useUsing the receiver Switching the receiver on/offAdjusting the volume Switching the channelConfigure the receiver Menu is given within the chapter The setup menuOperating menu of the receiver Attaching the receiver to clothingStarting the setup menu Function of the buttons in the setup menuGetting into the operating menu of the setup menu Getting into the setting mode of a menuSelecting a menu Software stored on a chip in the deviceAdjusting a setting Storing a settingCanceling the entry Exiting the setup menuSetup menu of the receiver LOC. OFF LOC. onAdjustment tips for the setup menu Activating/deactivating the lock modeLocking channels for the user Changing the receiving frequencies of the channelsAdjusting the squelch threshold Releasing locked channelsDisplaying the revision of the firmware Limiting the volume at the headphone outputCopy function Slave Quick charger LED indications Setting up the charger Switching the charger on or offCascading several chargers Do not place the receiver on delicate surfacesUsing the charger Care and maintenanceCharging the rechargeable battery BA Compartments As shown Red LEDChannel bank system SK 100 G2 / SK 300 G2 / SK 500 G2Quick charger SKM 100 G2 / SKM 300 G2 / SKM 500 G2 radiomicrophones Delivery includesInserting and changing the battery Changing the microphone moduleUsing the radiomicrophone Switching the radiomicrophone on/offMuting the radiomicrophone SK 100 G2 / SK 300 G2 / SK 500 G2 bodypack transmitters Inserting and charging the accupack Connecting the microphone/line cable Attaching the microphonesUse the microphone clips Positioning the microphonesUsing the bodypack transmitter Switching the transmitter on/offMuting the transmitter Play appears on the display panelSKP 100 G2 / SKP 500 G2 plug-on transmitters Microphone input, XLR-3 socket Button UP UnbalancedPlugging the transmitter onto the microphone Betriebs- und Batterieanzeige LC display panel Evolution wireless transmitters G Battery status indicationLC display panel Mute displayPilot display Display backlightingOverview of menus ButtonsGetting into the operating menu Working with the operating menuExiting the operating menu Exit Overview of the operating menu of the transmittersDisply Switching between channel banks Switching between the channels in a channel bankAdjusting the sensitivity Selecting the frequencies to be stored in the channelSwitching the phantom powering on/off SKP 500 G2 onlySelecting the standard display Loading the factory-preset default settingsEntering a name Activating/deactivating the pilot tone transmission Activating/deactivating the lock modeExiting the operating menu Troubleshooting Error checklistSet transmitter and receiver to Deactivate the muting functionRecommendations and tips For the receiver EKFor the radiomicrophones …for the bodypack transmittersProgress you can hear HDX noise reductionInherent Accessories and spare parts Quick chargerSK 100 G2 / SK 300 G2 / SK 500 G2 bodypack transmitter SKP 100 G2 / SKP 500 G2 plug-on transmitterEK 1038 receiver Specifications2015charger Evolution wireless transmitters G Deep discharge recovery chargeAutomatic security switch-off after 6 h at the latest Plug-in mains unitsChannel assignment Tune ChanWarranty Manufacturer declarationsWeee Declaration Statements regarding FCC and industry CanadaManufacturer declarations