Sennheiser LV307 Using the charger, Care and maintenance, Charging the rechargeable battery BA

Page 25

L 2015 quick charger

Using the charger

 

Charging the rechargeable battery BA 2015

 

Insert the rechargeable battery into one of the two charging

￿

compartments

as shown.

The red LED

at the occupied charging compartment lights up.

 

Charging a completely discharged rechargeable battery takes approx. 2½ hours at room temperature. It is normal for the accupacks to get warm during charging.

However, the charging process may take longer if:

y the rechargeable battery is deep-discharged and first has to be reconditioned by a deep discharge recovery charge,

y the ambient temperature is close to or over 40 °C, since, in order to protect the accupack, the charging process will be interrupted until the rechargeable battery temperature has fallen to an admissible value.

For safety reasons, the charging process will be interrupted and the red LED will start flashing if:

yexcessively hot accupacks cannot cool down,

yan rechargeable battery cannot be fully charged within the max. charging time of 6 hours, e.g. due to overaged cells.

After the rechargeable battery has been fully charged, the green

LED lights up.

Note:

For charging, the accupacks can remain in the unit. Place the unit with the rechargeable battery inserted into the charging compartment as shown. The receiver or the transmitter auto- matically switch off.

Care and maintenance

Use a slightly damp cloth to clean the switched-off charger from time to time. Use a brush or similar to remove dust from the charg- ing compartments. Do not use any cleansing agents or solvents.

25

Image 25
Contents Tourguide UHF Page Contents Thank you for choosing Sennheiser Important safety instructions Replacement parts Power sourceSafety check OverloadingDo not solder Safety instructions for Lithium-Ion rechargeable batteriesSystem components Tourguide UHF systemEK 1038 receiver Special featuresOperating controls Segments Capacity approx % Battery icon flashing LOW BAT Operation and battery status indicationRF signal indication IndicationsHow to properly use the battery pack or the batteries Inserting and changing the battery pack/batteriesConnecting the headphones Preparing for useSwitching the receiver on/off Using the receiverAdjusting the volume Switching the channelMenu is given within the chapter The setup menu Configure the receiverOperating menu of the receiver Attaching the receiver to clothingFunction of the buttons in the setup menu Starting the setup menuGetting into the setting mode of a menu Getting into the operating menu of the setup menuSelecting a menu Software stored on a chip in the deviceStoring a setting Adjusting a settingCanceling the entry Exiting the setup menuLOC. OFF LOC. on Setup menu of the receiverActivating/deactivating the lock mode Adjustment tips for the setup menuLocking channels for the user Changing the receiving frequencies of the channelsReleasing locked channels Adjusting the squelch thresholdDisplaying the revision of the firmware Limiting the volume at the headphone outputCopy function Slave Quick charger LED indications Switching the charger on or off Setting up the chargerCascading several chargers Do not place the receiver on delicate surfacesCare and maintenance Using the chargerCharging the rechargeable battery BA Compartments As shown Red LEDSK 100 G2 / SK 300 G2 / SK 500 G2 Channel bank systemQuick charger Delivery includes SKM 100 G2 / SKM 300 G2 / SKM 500 G2 radiomicrophonesChanging the microphone module Inserting and changing the batterySwitching the radiomicrophone on/off Using the radiomicrophoneMuting the radiomicrophone SK 100 G2 / SK 300 G2 / SK 500 G2 bodypack transmitters Inserting and charging the accupack Attaching the microphones Connecting the microphone/line cableUse the microphone clips Positioning the microphonesSwitching the transmitter on/off Using the bodypack transmitterMuting the transmitter Play appears on the display panelMicrophone input, XLR-3 socket Button UP Unbalanced SKP 100 G2 / SKP 500 G2 plug-on transmittersPlugging the transmitter onto the microphone Betriebs- und Batterieanzeige Battery status indication LC display panel Evolution wireless transmitters GLC display panel Mute displayDisplay backlighting Pilot displayButtons Overview of menusGetting into the operating menu Working with the operating menuExiting the operating menu Overview of the operating menu of the transmitters ExitDisply Switching between the channels in a channel bank Switching between channel banksAdjusting the sensitivity Selecting the frequencies to be stored in the channelSKP 500 G2 only Switching the phantom powering on/offSelecting the standard display Loading the factory-preset default settingsEntering a name Activating/deactivating the pilot tone transmission Activating/deactivating the lock modeExiting the operating menu Error checklist TroubleshootingSet transmitter and receiver to Deactivate the muting functionFor the receiver EK Recommendations and tipsFor the radiomicrophones …for the bodypack transmittersProgress you can hear HDX noise reductionInherent Quick charger Accessories and spare partsSKP 100 G2 / SKP 500 G2 plug-on transmitter SK 100 G2 / SK 300 G2 / SK 500 G2 bodypack transmitterEK 1038 receiver Specifications2015charger Deep discharge recovery charge Evolution wireless transmitters GAutomatic security switch-off after 6 h at the latest Plug-in mains unitsTune Chan Channel assignmentManufacturer declarations WarrantyStatements regarding FCC and industry Canada Weee DeclarationManufacturer declarations