Sennheiser LV308, LV307 manual Starting the setup menu, Function of the buttons in the setup menu

Page 14

Using the receiver

Starting the setup menu

In order to get into the configuration menu, the receiver must be switched off.

Open the battery compartment.
Press the SET button and keep it pressed.
At the same time, turn the volume control	clockwise until it

clicks to switch the receiver on. The “SETUP” display appears on the display panel.

Function of the buttons in the setup menu

Buttons	Mode	To ...

		get from the start display “SETUP“ to
	Start display	the operating menu of the setup
		menu

SET	Operating menu	get into the setting mode of the
		selected menu

	Setting mode	store the settings and return to the
	Setting mode	top menu level
		top menu level

	Start display	without function

	Operating menu	change to the previous menu ( ) or
/	Operating menu	change to the next menu ( )

	Setting mode	adjust the setting of the selected
	Setting mode	menu: option ( / )
		menu: option ( / )

	Start display	without function

	Operating menu	cancel the adjustment and return to
ESC	Operating menu	the start display “SETUP“

	Setting mode	cancel the entry and return to the
	Setting mode	start display “SETUP“
		start display “SETUP“

14

Image 14

Contents Tourguide UHF Page Contents Thank you for choosing Sennheiser Important safety instructions Safety check Power sourceReplacement parts OverloadingSafety instructions for Lithium-Ion rechargeable batteries Do not solderTourguide UHF system System componentsOperating controls Special featuresEK 1038 receiver RF signal indication Operation and battery status indicationSegments Capacity approx % Battery icon flashing LOW BAT IndicationsConnecting the headphones Inserting and changing the battery pack/batteriesHow to properly use the battery pack or the batteries Preparing for useAdjusting the volume Using the receiverSwitching the receiver on/off Switching the channelOperating menu of the receiver Configure the receiverMenu is given within the chapter The setup menu Attaching the receiver to clothingStarting the setup menu Function of the buttons in the setup menuSelecting a menu Getting into the operating menu of the setup menuGetting into the setting mode of a menu Software stored on a chip in the deviceCanceling the entry Adjusting a settingStoring a setting Exiting the setup menuSetup menu of the receiver LOC. OFF LOC. onLocking channels for the user Adjustment tips for the setup menuActivating/deactivating the lock mode Changing the receiving frequencies of the channelsAdjusting the squelch threshold Releasing locked channelsCopy function Limiting the volume at the headphone outputDisplaying the revision of the firmware Slave Quick charger LED indications Cascading several chargers Setting up the chargerSwitching the charger on or off Do not place the receiver on delicate surfacesCharging the rechargeable battery BA Using the chargerCare and maintenance Compartments As shown Red LEDChannel bank system SK 100 G2 / SK 300 G2 / SK 500 G2Quick charger SKM 100 G2 / SKM 300 G2 / SKM 500 G2 radiomicrophones Delivery includesInserting and changing the battery Changing the microphone moduleUsing the radiomicrophone Switching the radiomicrophone on/offMuting the radiomicrophone SK 100 G2 / SK 300 G2 / SK 500 G2 bodypack transmitters Inserting and charging the accupack Use the microphone clips Connecting the microphone/line cableAttaching the microphones Positioning the microphonesMuting the transmitter Using the bodypack transmitterSwitching the transmitter on/off Play appears on the display panelSKP 100 G2 / SKP 500 G2 plug-on transmitters Microphone input, XLR-3 socket Button UP UnbalancedPlugging the transmitter onto the microphone Betriebs- und Batterieanzeige LC display panel LC display panel Evolution wireless transmitters GBattery status indication Mute displayPilot display Display backlightingOverview of menus ButtonsExiting the operating menu Working with the operating menuGetting into the operating menu Exit Overview of the operating menu of the transmittersDisply Adjusting the sensitivity Switching between channel banksSwitching between the channels in a channel bank Selecting the frequencies to be stored in the channelSwitching the phantom powering on/off SKP 500 G2 onlyEntering a name Loading the factory-preset default settingsSelecting the standard display Exiting the operating menu Activating/deactivating the lock modeActivating/deactivating the pilot tone transmission Set transmitter and receiver to TroubleshootingError checklist Deactivate the muting functionFor the radiomicrophones Recommendations and tipsFor the receiver EK …for the bodypack transmittersInherent HDX noise reductionProgress you can hear Accessories and spare parts Quick chargerSK 100 G2 / SK 300 G2 / SK 500 G2 bodypack transmitter SKP 100 G2 / SKP 500 G2 plug-on transmitter2015charger SpecificationsEK 1038 receiver Automatic security switch-off after 6 h at the latest Evolution wireless transmitters GDeep discharge recovery charge Plug-in mains unitsChannel assignment Tune ChanWarranty Manufacturer declarationsWeee Declaration Statements regarding FCC and industry CanadaManufacturer declarations