Sennheiser LV308, LV307 manual Cascading several chargers, Setting up the charger

Page 24

L 2015 quick charger

Preparing for use

Cascading several chargers

Make sure that the charger is disconnected from the mains.

Unscrew the two screws		at the right bottom side of the
charger.
Slide the two rails	out of the guiding slots and screw them
tight using the two screws .
Unscrew the two screws		at the left bottom side of the second
charger.

Slide the second charger onto the rails of the first charger and screw the rails tight using the two screws .

Up to three chargers can be cascaded together with the rails and can by powered by a common mains unit..

Numbers of chargers	Mains unit requiredl
1	NT 1
up to 3	NT 3

Setting up the charger

The charger has four plastic feet to ensure that it cannot slip on the surface on which it is placed.

CAUTION! Risk of staining of furniture surfaces!

Some furniture surfaces have been treated with var- nish, polish or synthetics which might cause stains when they come into contact with other synthetics. Despite a thorough testing of the synthetics used by us, we cannot rule out the possibility of staining.

Do not place the receiver on delicate surfaces.

Switching the charger on or off

To switch the charger on, insert the hollow jack plug on the cable of the mains unit (mains unit must be ordered separately) into socket .

Connect the mains unit to the mains.

All LEDs briefly light up one after the other.

24

Image 24

Contents Tourguide UHF Page Contents Thank you for choosing Sennheiser Important safety instructions Power source Replacement partsSafety check OverloadingSafety instructions for Lithium-Ion rechargeable batteries Do not solderTourguide UHF system System componentsSpecial features EK 1038 receiverOperating controls Operation and battery status indication Segments Capacity approx % Battery icon flashing LOW BATRF signal indication IndicationsInserting and changing the battery pack/batteries How to properly use the battery pack or the batteriesConnecting the headphones Preparing for useUsing the receiver Switching the receiver on/offAdjusting the volume Switching the channelConfigure the receiver Menu is given within the chapter The setup menuOperating menu of the receiver Attaching the receiver to clothingStarting the setup menu Function of the buttons in the setup menuGetting into the operating menu of the setup menu Getting into the setting mode of a menuSelecting a menu Software stored on a chip in the deviceAdjusting a setting Storing a settingCanceling the entry Exiting the setup menuSetup menu of the receiver LOC. OFF LOC. onAdjustment tips for the setup menu Activating/deactivating the lock modeLocking channels for the user Changing the receiving frequencies of the channelsAdjusting the squelch threshold Releasing locked channelsLimiting the volume at the headphone output Displaying the revision of the firmwareCopy function Slave Quick charger LED indications Setting up the charger Switching the charger on or offCascading several chargers Do not place the receiver on delicate surfacesUsing the charger Care and maintenanceCharging the rechargeable battery BA Compartments As shown Red LEDChannel bank system SK 100 G2 / SK 300 G2 / SK 500 G2Quick charger SKM 100 G2 / SKM 300 G2 / SKM 500 G2 radiomicrophones Delivery includesInserting and changing the battery Changing the microphone moduleUsing the radiomicrophone Switching the radiomicrophone on/offMuting the radiomicrophone SK 100 G2 / SK 300 G2 / SK 500 G2 bodypack transmitters Inserting and charging the accupack Connecting the microphone/line cable Attaching the microphonesUse the microphone clips Positioning the microphonesUsing the bodypack transmitter Switching the transmitter on/offMuting the transmitter Play appears on the display panelSKP 100 G2 / SKP 500 G2 plug-on transmitters Microphone input, XLR-3 socket Button UP UnbalancedPlugging the transmitter onto the microphone Betriebs- und Batterieanzeige LC display panel Evolution wireless transmitters G Battery status indicationLC display panel Mute displayPilot display Display backlightingOverview of menus ButtonsWorking with the operating menu Getting into the operating menuExiting the operating menu Exit Overview of the operating menu of the transmittersDisply Switching between channel banks Switching between the channels in a channel bankAdjusting the sensitivity Selecting the frequencies to be stored in the channelSwitching the phantom powering on/off SKP 500 G2 onlyLoading the factory-preset default settings Selecting the standard displayEntering a name Activating/deactivating the lock mode Activating/deactivating the pilot tone transmissionExiting the operating menu Troubleshooting Error checklistSet transmitter and receiver to Deactivate the muting functionRecommendations and tips For the receiver EKFor the radiomicrophones …for the bodypack transmittersHDX noise reduction Progress you can hearInherent Accessories and spare parts Quick chargerSK 100 G2 / SK 300 G2 / SK 500 G2 bodypack transmitter SKP 100 G2 / SKP 500 G2 plug-on transmitterSpecifications EK 1038 receiver2015charger Evolution wireless transmitters G Deep discharge recovery chargeAutomatic security switch-off after 6 h at the latest Plug-in mains unitsChannel assignment Tune ChanWarranty Manufacturer declarationsWeee Declaration Statements regarding FCC and industry CanadaManufacturer declarations