Sennheiser LV307, LV308 manual Preparing for use, Plugging the transmitter onto the microphone

Page 37

SKP 100 G2 / SKP 500 G2 plug-on transmitters

Preparing for use

Inserting and changing the battery

For powering the plug-on transmitter, you can either use two 1.5 V AA size batteries or the rechargeable Sennheiser BA 2015 accupack.

Slide the battery compartment cover in the direction of the embossed arrow until it clicks audibly and open the cover.

Insert the two batteries or the BA 2015 rechargeable battery as shown below. Please observe correct polarity when inserting the batteries/accupack.

Close the battery compartment. The battery compartment cover 9 locks into place with an audible click.

Note:

For rechargeable battery operation of the transmitter, only use the BA 2015 rechargeable battery in order to ensure optimum operational reliability. For charging the accupack, only use the L 2015 charger. Both the rechargeable battery and the charger are available as accessories.

The rechargeable battery is fitted with an integrated sensor which is – via a third contact – monitored by the electronics of the plug-on transmitter and the charger. The sensor is necessary for the following control purposes:

yThe taking into account of the different voltage characteristics of primary cells (batteries) and accupacks. The battery status indications on the displays, the transmission of transmitter battery status information to the rack-mount receivers and the switch-off thresholds at the end of the operating time are corrected correspondingly. Due to the missing sensor, individual rechargeable battery cells will not be identified as accupacks.

yThe monitoring of the rechargeable battery temperature during charing in the L 2015 charger.

Plugging the transmitter onto the microphone

Plug the transmitter’s XLR-3 connector onto the microphone’s XLR-3 socket.

Tighten the locking ring .

Note:

The transmitter uses the microphone body as an antenna – therefore only microphones with a metal casing should be used for best signal transmission.

37

Image 37

Contents Tourguide UHF Page Contents Thank you for choosing Sennheiser Important safety instructions Replacement parts Power sourceSafety check OverloadingDo not solder Safety instructions for Lithium-Ion rechargeable batteriesSystem components Tourguide UHF systemEK 1038 receiver Special featuresOperating controls Segments Capacity approx % Battery icon flashing LOW BAT Operation and battery status indicationRF signal indication IndicationsHow to properly use the battery pack or the batteries Inserting and changing the battery pack/batteriesConnecting the headphones Preparing for useSwitching the receiver on/off Using the receiverAdjusting the volume Switching the channelMenu is given within the chapter The setup menu Configure the receiverOperating menu of the receiver Attaching the receiver to clothingFunction of the buttons in the setup menu Starting the setup menuGetting into the setting mode of a menu Getting into the operating menu of the setup menuSelecting a menu Software stored on a chip in the deviceStoring a setting Adjusting a settingCanceling the entry Exiting the setup menuLOC. OFF LOC. on Setup menu of the receiverActivating/deactivating the lock mode Adjustment tips for the setup menuLocking channels for the user Changing the receiving frequencies of the channelsReleasing locked channels Adjusting the squelch thresholdDisplaying the revision of the firmware Limiting the volume at the headphone outputCopy function Slave Quick charger LED indications Switching the charger on or off Setting up the chargerCascading several chargers Do not place the receiver on delicate surfacesCare and maintenance Using the chargerCharging the rechargeable battery BA Compartments As shown Red LEDSK 100 G2 / SK 300 G2 / SK 500 G2 Channel bank systemQuick charger Delivery includes SKM 100 G2 / SKM 300 G2 / SKM 500 G2 radiomicrophonesChanging the microphone module Inserting and changing the batterySwitching the radiomicrophone on/off Using the radiomicrophoneMuting the radiomicrophone SK 100 G2 / SK 300 G2 / SK 500 G2 bodypack transmitters Inserting and charging the accupack Attaching the microphones Connecting the microphone/line cableUse the microphone clips Positioning the microphonesSwitching the transmitter on/off Using the bodypack transmitterMuting the transmitter Play appears on the display panelMicrophone input, XLR-3 socket Button UP Unbalanced SKP 100 G2 / SKP 500 G2 plug-on transmittersPlugging the transmitter onto the microphone Betriebs- und Batterieanzeige Battery status indication LC display panel Evolution wireless transmitters GLC display panel Mute displayDisplay backlighting Pilot displayButtons Overview of menusGetting into the operating menu Working with the operating menuExiting the operating menu Overview of the operating menu of the transmitters ExitDisply Switching between the channels in a channel bank Switching between channel banksAdjusting the sensitivity Selecting the frequencies to be stored in the channelSKP 500 G2 only Switching the phantom powering on/offSelecting the standard display Loading the factory-preset default settingsEntering a name Activating/deactivating the pilot tone transmission Activating/deactivating the lock modeExiting the operating menu Error checklist TroubleshootingSet transmitter and receiver to Deactivate the muting functionFor the receiver EK Recommendations and tipsFor the radiomicrophones …for the bodypack transmittersProgress you can hear HDX noise reductionInherent Quick charger Accessories and spare partsSKP 100 G2 / SKP 500 G2 plug-on transmitter SK 100 G2 / SK 300 G2 / SK 500 G2 bodypack transmitterEK 1038 receiver Specifications2015charger Deep discharge recovery charge Evolution wireless transmitters GAutomatic security switch-off after 6 h at the latest Plug-in mains unitsTune Chan Channel assignmentManufacturer declarations WarrantyStatements regarding FCC and industry Canada Weee DeclarationManufacturer declarations