Sennheiser LV307, LV308 manual Troubleshooting, Error checklist, Set transmitter and receiver to

Page 49

Troubleshooting

Troubleshooting

Error checklist

Problem

Possible cause

Possible solution

No operation

Batteries are flat or rechargeable

Replace the batteries or recharge the

indication

battery is flat

accupack

 

 

 

 

Transmitter and receiver are not on the

Set transmitter and receiver to the

No audio signal

same frequency.

same frequency .

 

 

The transmitter is out of range.

Reduce the distance between

 

 

transmitter and receiver.

 

 

 

 

 

RF signal available,

The transmitter’s microphone is muted

Deactivate the muting function

(“MUTE”)

 

but no audio signal

Defective microphone

Replace microphone

 

 

 

 

Defective headphones

Replace headphones

 

 

 

Audio signal has a

Transmitter sensitivity is adjusted too

see “Adjusting the sensitivity” on

high level of

low

page 47

background noise

 

 

 

 

 

Audio signal is

Transmitter sensitivity is adjusted too

see “Adjusting the sensitivity” on

distorted

high

page 47

 

 

 

 

No contact with the rechargeable

 

 

battery (contacts are dirty or

Clean the contacts or insert the

 

rechargeable battery is not inserted

rechargeable battery correctly

 

correctly)

 

 

 

 

L 2015:

rechargeable battery is defective

 

red LED flashes

(overaged or defective rechargeable

Replace the accupack

besides a charging

battery cells)

 

compartment

 

 

rechargeable battery temperature is

Always charge the rechargeable

 

too low or too high

battery at room temperature

 

 

 

 

Batteries (primary cells) or individual

 

 

rechargeable batteries have been

Only charge the BA 2015 accupack!

 

inserted

 

 

 

 

If still operating problems with your transmission installation occur, please contact your local Sennhe- iser agent for assistance.

49

Image 49
Contents Tourguide UHF Page Contents Thank you for choosing Sennheiser Important safety instructions Replacement parts Power sourceSafety check OverloadingDo not solder Safety instructions for Lithium-Ion rechargeable batteriesSystem components Tourguide UHF systemEK 1038 receiver Special featuresOperating controls Segments Capacity approx % Battery icon flashing LOW BAT Operation and battery status indicationRF signal indication IndicationsHow to properly use the battery pack or the batteries Inserting and changing the battery pack/batteriesConnecting the headphones Preparing for useSwitching the receiver on/off Using the receiverAdjusting the volume Switching the channelMenu is given within the chapter The setup menu Configure the receiverOperating menu of the receiver Attaching the receiver to clothingFunction of the buttons in the setup menu Starting the setup menuGetting into the setting mode of a menu Getting into the operating menu of the setup menuSelecting a menu Software stored on a chip in the deviceStoring a setting Adjusting a settingCanceling the entry Exiting the setup menuLOC. OFF LOC. on Setup menu of the receiverActivating/deactivating the lock mode Adjustment tips for the setup menuLocking channels for the user Changing the receiving frequencies of the channelsReleasing locked channels Adjusting the squelch thresholdDisplaying the revision of the firmware Limiting the volume at the headphone outputCopy function Slave Quick charger LED indications Switching the charger on or off Setting up the chargerCascading several chargers Do not place the receiver on delicate surfacesCare and maintenance Using the chargerCharging the rechargeable battery BA Compartments As shown Red LEDSK 100 G2 / SK 300 G2 / SK 500 G2 Channel bank systemQuick charger Delivery includes SKM 100 G2 / SKM 300 G2 / SKM 500 G2 radiomicrophonesChanging the microphone module Inserting and changing the batterySwitching the radiomicrophone on/off Using the radiomicrophoneMuting the radiomicrophone SK 100 G2 / SK 300 G2 / SK 500 G2 bodypack transmitters Inserting and charging the accupack Attaching the microphones Connecting the microphone/line cableUse the microphone clips Positioning the microphonesSwitching the transmitter on/off Using the bodypack transmitterMuting the transmitter Play appears on the display panelMicrophone input, XLR-3 socket Button UP Unbalanced SKP 100 G2 / SKP 500 G2 plug-on transmittersPlugging the transmitter onto the microphone Betriebs- und Batterieanzeige Battery status indication LC display panel Evolution wireless transmitters GLC display panel Mute displayDisplay backlighting Pilot displayButtons Overview of menusGetting into the operating menu Working with the operating menuExiting the operating menu Overview of the operating menu of the transmitters ExitDisply Switching between the channels in a channel bank Switching between channel banksAdjusting the sensitivity Selecting the frequencies to be stored in the channelSKP 500 G2 only Switching the phantom powering on/offSelecting the standard display Loading the factory-preset default settingsEntering a name Activating/deactivating the pilot tone transmission Activating/deactivating the lock modeExiting the operating menu Error checklist TroubleshootingSet transmitter and receiver to Deactivate the muting functionFor the receiver EK Recommendations and tipsFor the radiomicrophones …for the bodypack transmittersProgress you can hear HDX noise reductionInherent Quick charger Accessories and spare partsSKP 100 G2 / SKP 500 G2 plug-on transmitter SK 100 G2 / SK 300 G2 / SK 500 G2 bodypack transmitterEK 1038 receiver Specifications2015charger Deep discharge recovery charge Evolution wireless transmitters GAutomatic security switch-off after 6 h at the latest Plug-in mains unitsTune Chan Channel assignmentManufacturer declarations WarrantyStatements regarding FCC and industry Canada Weee DeclarationManufacturer declarations