Uniden EXI 7926 manual Caller ID features, Using Caller ID, Screening your calls

Page 33
12/21 12:30PM 03￿ Schlitz Maren￿ 817-555-1212

Caller ID features

Using Caller ID

You must subscribe to Caller ID from your phone company to use this feature.

Screening your calls

Caller ID allows you to review caller information before answering your phone. At the second ring, the display shows the date, time, call count, name and phone

number of the caller. If your Caller ID service is number only, the name does not appear on the second line.

If a name or number is not available, the display shows a message such as

Incomplete Data”, “Private Number”, “Private Name”, etc.

Reviewing Caller ID name/numbers

To review your Caller ID name/numbers, follow the steps below:

1

2

Press call id/hold . The following screen appears:

call id

dn

up

delete

 

New Total￿

 

 

 

 

Line1

00

02￿

hold

conf

int'com

flash

Line2

01

01

Use ¥up/int'com or

dn »/conf

to select "Line 1" or "Line 2" for caller ID.

call id

dn

up

delete

 

 

 

hold conf int'com flash

3 Press sel/vol to display the latest Caller ID message for that line.

 

sel/vol chan redial/p

4

Press ¥up/int'com

to see the next message.

 

Or press dn »/conf

to see previous message.

5

Once you have reviewed your oldest name/

 

number, the following screen appears.

12/21 12:30PM 03￿ Schlitz Maren￿ 817-555-1212

￿

-End of List-￿

continued next page

Notes • If you have no Call ID name/ numbers, then the total is shown as “00”.

Once a Caller ID message has been viewed, it is no longer considered a new message.

33

Image 33
Contents Page Introduction FeaturesLine2 Controls and functions39 40 41 42 43 Table of contents 11 to Read this firstStep Checking the package contentsChoose the best location Setting up the base unitConnect the base unit Used only when second lineChoose the dialing mode If your dialing system is Set the switch toIf you arent sure of your dialing system Preparing the battery pack When the battery charge becomes low Battery use time per chargeCleaning the battery contacts Do not use any liquids or solventsSetting up Caller ID options To select Entering your area codeMaking and receiving calls BasicsBasic 2-line operation Handset On Base Handset Off Base Base Only Auto Talk offAnswering a call from the handset Answering a call from the baseMaking a call from the base Using the tone featureMaking a call from the handset Off-hook dialingLast number redial Flash and Call WaitingHandset BasePlacing a call on hold Using the speakerphone mute featureAdjusting the volume controls Using the page featureTraveling out-of-range Selecting a different channelBase ringer volume Line featuresBase speaker volume Line operationWay conferencing Conference Line 1 Line Using your EXI 7926 intercom Paging from the base to handsetPaging from the handset to base Transferring calls Using the speakerphoneMemory features Storing a phone number in memoryOn the handset On the base Editing a phone number in memory Press delete/flash to remove any unwanted From the handset Erasing a number from memoryFrom the base At the base Using memory dialingUsing Caller ID Caller ID featuresScreening your calls Reviewing Caller ID name/numbersCalling a Caller ID name/number Select Location screen appears. Use Storing a Caller ID number in a memory locationDeleting a Caller ID message Deleting all Caller ID name/numbers Using Cidcw Caller ID with Call WaitingAdditional information Headset installationChanging the digital security code Headset JackStandard wall plate mounting Mounting the base unit on a wallDirect wall plate mounting To attach the beltclip To remove the beltclip Installing the beltclipBattery replacement and handling MaintenanceWhen slightly dirty When very dirtySymptom Suggestion TroubleshootingGeneral SpecificationsBase unit HandsetW, X, Y, Z Index