Uniden EXI 7926 Deleting all Caller ID name/numbers, Using Cidcw Caller ID with Call Waiting

Page 37
call id/hold

Caller ID features (continued)

Deleting all Caller ID name/numbers

To delete all of your Caller ID messages, follow the steps below.

1 Press . The Caller ID summary screen shows the number of new callers and total number of calls.

call id dn

up delete

hold conf int'com flash

New Total￿

Line1 00 02￿

Line2 01 01

2 Use ¥up/int'com or dn »/conf to select

call id dn

up delete

Line 1”.

hold conf int'com flash

3

4

5

Press delete/flash

to delete name/numbers on line 1. The following screen

appears:

 

 

 

 

 

 

call id

dn

up

delete

Del All, Line 1?￿

 

 

 

 

Yes￿

 

 

hold

conf int'com

flash

No

 

 

Use the ¥up/int'com

key to move the cursor to “Yes”.

 

 

Press delete/flash

or

sel/vol .

 

 

New Total￿

A confirmation tone sounds. The following

 

Line1

00

00￿

screen appears:

 

 

 

Line2

00

01

6

Use dn »/conf to select line 2.

 

New Total￿

7

Repeat steps 3 through 6.

Line1

00

00￿

Line2

00

00

All your caller ID messages are deleted.

Using CIDCW (Caller ID with Call Waiting)

1 During a call, when you hear the Caller ID tone, check the handset display for the name and number of incoming calls.

2 Press delete/flash to accept the incoming call. See Flash and Call Waiting, page 18.

12/21 12:30PM 03￿ Schlitz Maren￿ 817-555-1212

call id dn

up delete

hold conf int'com flash

37

Image 37
Contents Page Introduction FeaturesLine2 Controls and functions39 40 41 42 43 Table of contents 11 to Read this firstStep Checking the package contentsChoose the best location Setting up the base unitConnect the base unit Used only when second lineIf your dialing system is Set the switch to Choose the dialing modeIf you arent sure of your dialing system Preparing the battery pack When the battery charge becomes low Battery use time per chargeCleaning the battery contacts Do not use any liquids or solventsSetting up Caller ID options To select Entering your area codeMaking and receiving calls BasicsBasic 2-line operation Handset On Base Handset Off Base Base Only Auto Talk offAnswering a call from the handset Answering a call from the baseMaking a call from the base Using the tone featureMaking a call from the handset Off-hook dialingLast number redial Flash and Call WaitingHandset BasePlacing a call on hold Using the speakerphone mute featureAdjusting the volume controls Using the page featureTraveling out-of-range Selecting a different channelBase ringer volume Line featuresBase speaker volume Line operationWay conferencing Conference Line 1 Line Paging from the base to handset Using your EXI 7926 intercomPaging from the handset to base Transferring calls Using the speakerphoneStoring a phone number in memory Memory featuresOn the handset On the base Editing a phone number in memory Press delete/flash to remove any unwanted From the handset Erasing a number from memoryFrom the base At the base Using memory dialingUsing Caller ID Caller ID featuresScreening your calls Reviewing Caller ID name/numbersCalling a Caller ID name/number Select Location screen appears. Use Storing a Caller ID number in a memory locationDeleting a Caller ID message Deleting all Caller ID name/numbers Using Cidcw Caller ID with Call WaitingAdditional information Headset installationChanging the digital security code Headset JackStandard wall plate mounting Mounting the base unit on a wallDirect wall plate mounting To attach the beltclip To remove the beltclip Installing the beltclipBattery replacement and handling MaintenanceWhen slightly dirty When very dirtySymptom Suggestion TroubleshootingGeneral SpecificationsBase unit HandsetW, X, Y, Z Index