Uniden EXI 7926 manual Storing a Caller ID number in a memory location

Page 35

2 Use

1 Press callers

Caller ID features (continued)

Storing a Caller ID number in a memory location

call id/hold . The Caller ID summary screen shows the number of new and total number of calls.

call id	dn	up	delete
hold	conf int'com		flash
¥up/int'com	or	dn »/conf	to select

“Line 1” or “Line 2” caller ID.

New Total

Line1 00 02

Line2 01 01

call id dn

up delete

3

4

5

		hold	conf int'com flash
Press	sel/vol to display the caller ID
message.		sel/vol	chan redial/p

Press	¥up/int'com or dn »/conf to find the name/number that you would like
to store.
Press	mem to store the selected message. The following screen appears:

line1	line2	Select Location
	mem	Select Location
		01	Schlitz Maren
		02	UNIDEN
6 The “Select Location” screen appears. Use the		¥up/int'com and dn »/conf

keys to select a blank memory location where you would like to store the number. (If you want to replace an existing number with the Caller ID number, skip to step 6.)

7

8

9

Press sel/vol . A confirmation tone sounds. The number is programmed.

If you choose to replace an existing number	Replace Memory?
with the Caller ID number, press sel/vol .	Yes
The following screen appears:	No

Use the ¥up/int'com key to move the cursor to “Yes”. Press sel/vol . A confirmation tone sounds. The number is programmed.

Note If you select “No”, then the Caller ID screen returns.

35

Image 35

Contents Page Introduction FeaturesLine2 Controls and functions39 40 41 42 43 Table of contents 11 to Read this firstStep Checking the package contentsChoose the best location Setting up the base unitConnect the base unit Used only when second lineIf you arent sure of your dialing system Choose the dialing modeIf your dialing system is Set the switch to Preparing the battery pack Do not use any liquids or solvents Battery use time per chargeWhen the battery charge becomes low Cleaning the battery contactsSetting up Caller ID options To select Entering your area codeHandset On Base Handset Off Base Base Only Auto Talk off BasicsMaking and receiving calls Basic 2-line operationAnswering a call from the handset Answering a call from the baseOff-hook dialing Using the tone featureMaking a call from the base Making a call from the handsetBase Flash and Call WaitingLast number redial HandsetPlacing a call on hold Using the speakerphone mute featureSelecting a different channel Using the page featureAdjusting the volume controls Traveling out-of-rangeLine operation Line featuresBase ringer volume Base speaker volumeWay conferencing Conference Line 1 Line Paging from the handset to base Using your EXI 7926 intercomPaging from the base to handset Transferring calls Using the speakerphoneOn the handset Memory featuresStoring a phone number in memory On the base Editing a phone number in memory Press delete/flash to remove any unwanted From the handset Erasing a number from memoryFrom the base At the base Using memory dialingReviewing Caller ID name/numbers Caller ID featuresUsing Caller ID Screening your callsCalling a Caller ID name/number Select Location screen appears. Use Storing a Caller ID number in a memory locationDeleting a Caller ID message Deleting all Caller ID name/numbers Using Cidcw Caller ID with Call WaitingHeadset Jack Headset installationAdditional information Changing the digital security codeStandard wall plate mounting Mounting the base unit on a wallDirect wall plate mounting To attach the beltclip To remove the beltclip Installing the beltclipWhen very dirty MaintenanceBattery replacement and handling When slightly dirtySymptom Suggestion TroubleshootingHandset SpecificationsGeneral Base unitW, X, Y, Z Index