Panasonic WJ-HD200 Alarm Connection, External Recording Connection, Time Adjusting Connection

Page 17

Notes:

• Input rating: Low-active, non-voltage normally open (N.O.) contact

• Output rating for pin # 4

ALARM RECOVERY 1* OUT: High-active with a 200 Ω resistor pulled up to + 5 V

• Output rating for pin # 7

ALARM 2* OUT: High-active with a 4.7 kΩ resistor pulled up to + 12 V.

•Output rating for other pins: Low-active, maximum load capacity of 24 V 100 mA , open-collector with a 4.7 kΩ resistor pulled up to +5 V inside

●Alarm Connection

There are eight alarm inputs while two outputs are provided with different driving capacity.

Sensor

Door Switch

 

#3 Alarm 2 In

#2 Alarm 1 In

 

External

Alarm Indicator

Alarm

Reset Switch

Relay *1

Alarm Input Terminals

#7 Alarm Output 2 *2

Sinal Ground Terminals

*1: Use when the indicator exceeds over the drive capacity of the alarm out terminal.

*2: Connect to #6 ALARM OUT 1 when using a low-active device.

●External Recording Connection

The recording mode will change from the internal timer mode to the external mode (EXT REC MODE) specified in REC SETUP menu, while turning on the switch.

#22 External Recording Mode

●Time Adjusting Connection

Internal timer is calibrated with this input.

#13 Time Adjust In

Master Clock

Non-voltage N.O. Contact N.O.=Normally Open

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Operating Instructions Lightning flash with arrowhead symbol Important Safety Instructions Contents Trademarks FeaturesPreface Precautions Front View 5FULL Indicator Full 4HDD Access Indicator HDD6Error indicator Error 7Stop and Setup/Escape Button Stop SETUP/ESC@7Video Out Video OUT @6Audio OutRear View Installing the Optional HDD InstallationPlaces to avoid About mountingMounting in the Rack Basic System Connections & DIP SW SettingSystem Cameras PS Data SystemNetwork System Personal computers can access the WJ-HD200 via the networkConnection with the Camera Site ALARM/REMOTE ConnectionConnection with the Monitors System Camera ConnectionExternal Recording Connection Alarm ConnectionTime Adjusting Connection PS Data Connection Serial Port ConnectionsRS232C Connection Case 2 Exclusively with System Controller 10/100BASE-T Port ConnectionData Port Termination System ModePrior to Setup Setup ProceduresTurning On the Power Turning Off the PowerDisplaying WJ-HD200 Main Menu Buttons and Dials Used for SetupClosing WJ-HD200 Main Menu JogDial Counter-clockwise Decreases the parameterMenu Tree Initializing Initializing All Contents & Setup DataInitializing Setup Data Main Menu WJ-HD200 Main Menu Timer Recording Setup Timer RECProgram 1-4 Setup Program 1- 4 Setup Pre-alarm Recording PRE ALM REC Recording Mode Setup Prog 1-4 no -4 SetupAlarm Recording Mode Setup ALM REC Mode Trigger Action Setup Trigger Action Setup Post-alarm Recording Post ALM RECCamera Recording Setup CAM REC Setup Dynamic Recording Dynamic RECExternally Specified Recording Mode EXT REC Manual Recording Setup REC SetupDisplay Setup Display Setup Clock ClockStatus Display Status Disp Time & Date Display Time & Date DispStatus Position Status Posi Time & Date Position Time & Date PosiRemote LED Remote LED Disk Capacity Warning HDD FullDisk Check HDD Check ~ 9 a ~ Z ! % System Setup System SetupPassword Lock Setup Password Lock Simultaneous Recording & Playback Keylock Buzzer Setup Keylock BuzzSkip Alarm Recall Setup Disk End Mode Setup Alteration Detection SetupPlay Priority Setup Play Priority Disk End Buzzer Disk END Buzz14, 30, 45, 60, 90, 120, 150, 180DAYS Same as Time Adjust Setup Time AdjustingAuto Erasing Setup Auto Erasing Alarm Buzzer Alarm Buzz Alarm Setup Alarm SetupMonitor Mode Monitor Mode Video Motion Detection VMD SetupCommunication Setup Communication SetupSerial Setup Serial Setup Protocol ProtocolBaud Rate Baud Rate Alarm Data Alarm Data exclusive for PS DataData Bit Data BIT Parity Check Parity CheckNetwork Setup Network Setup Switcher Setup Switcher Setup Camera View Setup Camera View Spot Sequence Setup Spot SEQMulti SEQ Setup Available camera From 1 toSystem Information System InformationControlling Video Inputs & Monitors Operating ProceduresOn the Spot Monitor On the Multi-screen MonitorViewing Quad Live Sequence Viewing a Single Live SequenceViewing a Multi-screen Live Alarm Output Alarm Control FunctionAlarm Input Resetting Alarm Alarm Log Recall & Search Suspending Alarm InputPressing REC Stop Button To brows through the logPower-on Recording Internal Timer RecordingRecording To search for playbackManual Recording Alarm RecordingPlayback Alarm Search PlaybackNormal Playback Skip PlaybackMulti-screen Playback Time & Date Search PlaybackEnabling Button Lock Password VerificationLOCK/UNLOCK Buttons WJ-HD200 Display PreparationsBrowser Direct Connection with a PC ConnectionSystem Expansion Connection with a Client PC via HubRecorder Status Displayed Quality Main Page and Control PanelAbout Picture Quality To Access Setup Menus WJ-HD200 SetupTimer Setup Timer Setup Main Setup MenuProgramming Program Setup Program Assignment Timer RECRecording Mode Setup Prog 1-4 no -4 SET Assignable Programs PROG1 Prog 4, OFFMode Mode Trigger Action Setup Trigger Action SetupCamera Recording Setup CAM REC Setup Externally Specified Recording Mode EXT REC Setup Manual Recording SetupREC Setup Camera Title Camera Title System Setup System Setup Skip Alarm Recall Skip Alarm Recall Password Operation Password OperationDisk End Mode Disk END Mode Time Adjusting Time AdjustingVMD Setup Video Motion Detector SetupSerial Port Setup Serial Port SetupCamera Number Setup CAM NO. Setup only for Psdata Multi Sequence Setup Multi Sequence Setup Camera View Setup Camera View Setup Spot Sequence Setup SpotSequence Setup Information System Log System LOG Host Setup Host Setup Network ConfigurationUser Setup User Setup FTP Send by Periodic Timer FTP Send by Periodic Timer FTP Client Setup FTP Client SetupNetwork Video Setup Network Video Setup Mail Setup Mail SetupMain Panel Operating WJ-HD200Main Control Panel Alarm Reset button Alarm ResetCamera Selection button Camera Select Multiscreen Selection ButtonCamera Control View button Camera Control View Time & Date Search button Time&Date SearchPAN/TILT Control Left Right DownAlarm List Select Mode TroubleshootingWhen accessing via the network Phenomenon CauseSpecifications & Appendix Specifications Standard Accessories Menu Remote Control From System ControllerAppendix ON/OFF Daylight SavingsRS-232C Communication Protocol Transmission CommandResponse Command Basic Operation Command TableAlarm Control Miscellaneous Control Setup ControlData Log Control Media ControlQKM InquiryPower-on Procedures HDD MaintenanceWhen to Maintain HDD Who to Maintain HDD When Error Indicator is Lit When Full Indicator is Lit Resetting Disk EndAbbreviation Status Required Capacity Disk MenuDisk Menu Auto-removeFormatting HDD HDD Format Removing Logical Link Remove LinkNOW Formatting HDD Format →SET Done Restarting RestartHttp Download and Viewing Images Mail Contents N0103-0 V8QA6017AN

WJ-HD200 specifications

The Panasonic WJ-HD200 is a versatile and robust digital video recorder (DVR) designed primarily for high-quality surveillance applications. This device stands out for its exceptional recording capabilities, exemplifying Panasonic’s commitment to innovation in video technology.

One of the main features of the WJ-HD200 is its ability to support multiple video input channels. This DVR can accommodate up to 16 cameras simultaneously, making it an ideal choice for larger installations requiring comprehensive monitoring. Its capability to handle various camera types, including analog and IP cameras, enhances its flexibility and usability in diverse environments.

Another significant characteristic of the WJ-HD200 is its high-resolution recording. The device allows for real-time recording at a resolution of up to 720 x 480 pixels, ensuring that captured footage remains sharp and detailed. Users can adjust bit rates and frame rates according to specific surveillance needs, providing tailored video quality without sacrificing storage space or clarity.

A notable feature is the integration of advanced motion detection technology. This allows the WJ-HD200 to start recording only when motion is detected, optimizing storage usage and making it easier for users to review footage when needed. Coupled with this is the device’s intelligent search functionality, which enables quick navigation through recorded content by identifying motion events, thus saving time during investigations.

The WJ-HD200 utilizes a RAID (Redundant Array of Independent Disks) configuration, which improves data reliability and redundancy. This technology minimizes the risk of data loss due to disk failure, ensuring continuous operation and security for vital footage. Moreover, the DVR supports efficient data management with a built-in networking capability. Users can remotely access the system via a network connection, allowing for real-time monitoring and management from virtually anywhere.

Finally, the user-friendly interface of the WJ-HD200 further enhances its appeal. The system is designed for easy setup and operation, featuring a logical menu structure that simplifies navigation. With various output options, including VGA and composite outputs, users can connect the DVR to different display systems effortlessly.

In summary, the Panasonic WJ-HD200 combines high channel capacity, exceptional recording quality, advanced motion detection, reliable storage solutions, and user-friendly features. This DVR is a solid choice for anyone seeking a dependable and efficient surveillance solution.
Top Page Image Contents