JVC LYT0002-0H6B, 0397MKV*UN*SN manual Interval Capture, Automatically

Page 28

28EN VIDEOCAPTURE (cont.)

INTERVAL CAPTURE

The Interval Capture mode is best suited for capturing images at set intervals from a video source unit with a JLIP connector.

Set-up

 

Capture Mode

Step by Step

Image Format

Automatic

Device Change

 

Initialize

 

ID Change

 

Counter Reset

 

 

 

VCR

 

I

00:01:23:12F

Capture

Transfer

NOTE:

•Make sure that enough hard disk space is available on your computer before executing video transfer.

For full image data space requirements,

☞ p. 24.

•Transfer of index image data/full image data starts at the image box bordered in green.

Click and select the desired image box. •When transferring full image data using the Bitmap image format (9.bmp), the transfer takes a very long time, causing the video source unit to stop playback

automatically.

Preparation

•Make sure all units are properly connected (☞ p. 12).

•Insert a tape into the video source unit. Click "Image Format" in "Set-up" and select "Field Picture" in the Capture Mode.

(☞ p. 29).

1 Open the menu bar and click "Set-up" — "Capture Mode" — "Automatic".

•The "Automatic Transfer" window appears.

2 Select the data to be transferred. •When you select "Index Image", index

image data (80 x 60 pixels) is transferred to your computer.

•When you select "Index & Full Image", both index image data (80 x 60 pixels) and full image data (768 x 552 pixels) are transferred to the computer.

3 Select "Interval Capture".

4 Set the interval.

•Select the time interval at which pictures are captured.

5 Set the number of pictures to be captured and click "OK".

•From 1 up to 99

6 Click "Window" — "VCR" to call up the VCR Operation Window. Start video playback a few seconds prior to the point where you want image capturing to start.

7 Operate the video source unit via the VCR Operation window and click the "Transfer" button at the desired picture.

1.The message "No. 1 index image being transferred" appears while the index image data is being transferred to the computer.

2.When you select "Index & Full Image" in step 2, the message "No. 1 full image being transferred" appears while the full image data is being transferred to the computer.

3.The message "Index No. 2 being scanned" appears while the video data are fast- forwarded and played at the time intervals set in step 4 to scan the video data on the VCR.

•The image selected when "Transfer" is clicked is captured and subsequent images are captured at the time interval specified by the counter value selected in step 4.

•The video source unit enters the Pause mode when capture is complete.

Page 27 Page 29
Image 28
Page 27 Page 29
Contents GV-DS1 Dear Customer It is recommended that youDo not place the Video Capture Docking Station Maintenance How to handle a CD-ROMAC Power Adapter/Charger Contents Additional Operations Save PictureJlip Player Software Getting StartedVideo Printer Operation GV-PT2 Troubleshooting Major Specifications IndexAdvanced Operations Major Features Business presentationsInternet homepage Video journal and postcardsJlip Video Capture Software Video Capture FacilityJlip Control Facility Data Sharing With Jlip Player Soft- wareContro L S AN D Connec Tors Video output jack Outputs S-Video signal. Also Connections W hen Using JL IP Video Capture Software Input What is video capture software ? What is Jlip ?Operating Environment Connectable DevicesInstallation Procedure WindowsOpen & C Lose Bas ic Operatio n Proc edure PreparationHOW to Close the Program Click Exit from File in the menu bar. The program closesInitializing Jlip Select Transfer Rate. Normally selectSelect Units Menu bar Main Desktop WindowControl buttons Menu BAR Image display areaEach pulldown menu is configured as follows EN H OW the Deskto P W ORK SVCR operation window 00012312FImage data flow Capturing Video ImagesStep by Step Capture Index image data is transferred to the computerFull image data is transferred to the computer Repeat steps 2 through 5 as requiredAutomatic Capture EN V Ideo CA PtureProgram Capture Transfer Interval Capture AutomaticallyPicture Data Format Capture ModeSelecting a Picture Format Counter Reset EN Addi Tional Oper AT IonsCounter Value Change Modify Capture Point window appearsChange ID Delete Index Image and Full ImageYou can change the Video Capture Unit’s ID number Create NEW Folder SavingOpen the menu bar and click File New Album Saved, you will be asked whether to save or notOpen Index Save the Full Image DataUsing Jlip Player Software Data EN Jlip Player Soft WareMake sure all units are properly connected p Open Jlip jlp File window is displayedHOW to Store Jlip Player Data Save As Jlip jlp File window is displayedProblem Cause Counter cannot be reset Where the program run fileCannot capture video data With the desired counterMessage Appears when Action Error Execute afterPlaying back Not enough diskEN Memo Jlip Player Software Section EN Connections When Using Jlip Playe r Soft ware JVC Video unit Gettin G Started Installing Jlip Player Software EN To start the setup programPrepare Devices Starting Jlip Player SoftwareSelect Serial Port Select Devices Title bar Icon buttonDisplay File nameMemo Elapsed TimeSetting in/out points Operating camcorderSelect Scene Start PlaybackClick Start Only the camcorder movesBasic OP Eration S DubbingPrepare NEW Tape Start EditingStart Saving Enter File NameSave File Select Floppy Disk DriveOpening a saved file EN BA SIC OP E RationsCorrecting and cutting the programmed counter data Overwriting the file Designateied Scene to be COPStore Designated Scene in Memory Designate Scene to be TransferredPosition button Power button Icon buttonStore button Print buttonContent button Position buttonMULTI-PIX button Strobe Speed buttonPrinting Bring UP Video Printer WindowPlayback Store SceneClick Close Choose Exit from File Video Printer window closes Movie Player window closesAuto Capture PreparationTo Print Captured Video Data with Video Printer Load the tape into the video unitTo print only the cut-in scene on the edited tape EN Advan CED Oper AT Ions Connecting other device during operationChanging ID number Access Name Change Dialog BOX Access Device Selection Dialog BOXWhen Using the Video Capture Software Enter NEW Name SET NEW NameAccess Pause Time CORREC- Tion Dialog BOX EN Advanc ED Operat IonsEnter Value Determine ValueError - This application will That power is onPower on all devices System Communication error Check devices - ConfirmAjor Speci Ficat Ions Setup Menu Automatic Capture Auto BitmapChange ID COM Port Delete Index Image and Full Image Desktop Window Pg , 48GV-DS1
Top Page Image Contents