JVC 0397MKV*UN*SN manual Position button, MULTI-PIX button, Content button, Strobe Speed button

Page 57

1.POWER button

Turns the device on and off.

2.POSITION button

Selects the position to store a scene in memory for Multi-Print.

3.ID number

Displays the selected device's ID number.

4.Message display

Displays the operating mode of the selected device.

5.MULTI-PIX button

Select by clicking (/ ˜) button.

OFF : Single print

4: 4 shots on one sheet

16: 16 shots on one sheet

6.CONTENT button

• Select by clicking (/ ˜) button.

STROBE : Stores the selected number of images at short intervals, and prints them all on one sheet.

SELECTED : Prints 4 or 16 selected scenes

 

on one sheet.

SAME

: Prints the same scene 4 or 16

 

times on one sheet.

7.STROBE SPEED button

Effective when "STROBE" is selected from "CONTENT".

HIGH : When printing in the Strobe Print mode, the GV-PT2 stores scenes at intervals of approximately 1/ 15 second.

LOW : When printing in the Strobe Print mode, scenes are stored at intervals of approximately 1/2 second.

8. PIX STABILIZER button

ON

: If the scene you want to print is

 

jittery, select "ON" to stabilize it.

OFF

: Usually set to "OFF".

9. STORE button

EN 57

10.PRINT button

When connected to the GV-PT2

Print command is available.

11.SELECT (scene select) button

Switches between "SOURCE" (images from camcorder or VCR) and "MEMORY" (scenes stored in memory) for display on TV monitor.

12.CLOSE button

Closes the "Video Printer" window.

Stores scenes and titles you want to print in the video printer's memory.

Image 57
Contents GV-DS1 It is recommended that you Dear CustomerDo not place the Video Capture Docking Station How to handle a CD-ROM MaintenanceAC Power Adapter/Charger Contents Save Picture Additional OperationsJlip Player Software Getting StartedTroubleshooting Major Specifications Index Video Printer Operation GV-PT2Advanced Operations Business presentations Major FeaturesInternet homepage Video journal and postcardsVideo Capture Facility Jlip Video Capture SoftwareJlip Control Facility Data Sharing With Jlip Player Soft- wareContro L S AN D Connec Tors Video output jack Outputs S-Video signal. Also Connections W hen Using JL IP Video Capture Software Input What is Jlip ? What is video capture software ?Operating Environment Connectable DevicesWindows Installation ProcedurePreparation Open & C Lose Bas ic Operatio n Proc edureClick Exit from File in the menu bar. The program closes HOW to Close the ProgramSelect Transfer Rate. Normally select Initializing JlipSelect Units Main Desktop Window Menu barControl buttons Image display area Menu BAREN H OW the Deskto P W ORK S Each pulldown menu is configured as follows00012312F VCR operation windowCapturing Video Images Image data flowIndex image data is transferred to the computer Step by Step CaptureFull image data is transferred to the computer Repeat steps 2 through 5 as requiredEN V Ideo CA Pture Automatic CaptureProgram Capture Transfer Automatically Interval CaptureCapture Mode Picture Data FormatSelecting a Picture Format EN Addi Tional Oper AT Ions Counter ResetCounter Value Change Modify Capture Point window appearsDelete Index Image and Full Image Change IDYou can change the Video Capture Unit’s ID number Saving Create NEW FolderOpen the menu bar and click File New Album Saved, you will be asked whether to save or notSave the Full Image Data Open IndexEN Jlip Player Soft Ware Using Jlip Player Software DataMake sure all units are properly connected p Open Jlip jlp File window is displayedSave As Jlip jlp File window is displayed HOW to Store Jlip Player DataProblem Cause Where the program run file Counter cannot be resetCannot capture video data With the desired counterMessage Appears when Action Execute after ErrorPlaying back Not enough diskEN Memo Jlip Player Software Section EN Connections When Using Jlip Playe r Soft ware JVC Video unit Gettin G Started To start the setup program Installing Jlip Player Software ENStarting Jlip Player Software Prepare DevicesSelect Serial Port Select Devices Icon button Title barDisplay File nameElapsed Time MemoOperating camcorder Setting in/out pointsStart Playback Select SceneClick Start Only the camcorder movesDubbing Basic OP Eration SPrepare NEW Tape Start EditingEnter File Name Start SavingSave File Select Floppy Disk DriveEN BA SIC OP E Rations Opening a saved fileCorrecting and cutting the programmed counter data Designateied Scene to be COP Overwriting the fileStore Designated Scene in Memory Designate Scene to be TransferredIcon button Position button Power buttonStore button Print buttonPosition button Content buttonMULTI-PIX button Strobe Speed buttonBring UP Video Printer Window PrintingPlayback Store SceneVideo Printer window closes Movie Player window closes Click Close Choose Exit from FilePreparation Auto CaptureTo Print Captured Video Data with Video Printer Load the tape into the video unitTo print only the cut-in scene on the edited tape Connecting other device during operation EN Advan CED Oper AT IonsChanging ID number Access Device Selection Dialog BOX Access Name Change Dialog BOXWhen Using the Video Capture Software Enter NEW Name SET NEW NameEN Advanc ED Operat Ions Access Pause Time CORREC- Tion Dialog BOXEnter Value Determine ValueThat power is on Error - This application willPower on all devices System Communication error Check devices - ConfirmAjor Speci Ficat Ions Automatic Capture Auto Bitmap Setup MenuChange ID COM Port Delete Index Image and Full Image Desktop Window Pg , 48GV-DS1