JVC 0397MKVUNSN manual Error - This application will, Check devices - Confirm, That power is on

Page 65

TROUBLESHOOTING EN 65

	MESSAGE	⬤ POSSIBLE CAUSE
	MESSAGE	⬛ CORRECTIVE ACTION
		⬛ CORRECTIVE ACTION

	Error – – This application will	⬤ The COM port used for the JLIP connector is not
	close.	selected, or the COM port is selected but the
	Check devices – – Confirm	connection is wrong.
	that power is ON.	⬛ Check the connected COM port and select it on the
		"Serial Port Selection" screen (☞ pg. 46).

	No devices detected to	⬤ Power is not supplied or the connection is wrong.
	connect.	⬛ Connect the devices correctly and turn them on
	Power ON all devices in	(☞ pg. 42, 43).
	system.

	Communication error	⬤ Device is not turned on or cable is disconnected.
	(&H (number))	⬛ Connect the device correctly and turn it on
	Check cable connection.	(☞ pg. 42, 43).
		⬛ If device was turned off and on again during
		operation, click "OK". All devices should function
		properly.

	Select the device to control.	⬤ The line where the name of the device to use
		appears is not clicked.
		⬛ Click on it and "OK" (☞ pg. 47).

	No video cassette!!	⬤ The video cassette is not loaded in the camcorder.
	Load a video cassette to ID	When the video cassette is removed during
	(number).	operation, this message appears.
		⬛ Insert the video cassette into the camcorder.

	Invalid entry in scene	⬤ The value of the CUT OUT point is smaller than
	(number) (There is IN > OUT	the CUT IN point's.
	condition). Correct the time	⬛ Set the value of the CUT OUT point so that it is
	or delete the scene.	larger than the CUT IN point's (☞ pg. 50, 54).

	Select a number between 0	⬤ When correcting the CUT IN/OUT points, the
	and 24.	value you set differs from the original by over 25
		frames.
		⬛ Select integral number from 0 to 24 (☞ pg. 54).

	Invalid frame number on drop	⬤ Because the DV-format digital camcorder uses the
	frame counter.	drop frame system, inputting frame 00 and 01 is
		impossible.
		⬛ Input frame value other than 00 or 01
		(☞ pg. 48, 54).

The monitor displays of the application software illustrated in this manual may differ from those you are actually viewing depending on the operating environment of your computer.

Image 65

Contents GV-DS1 It is recommended that you Dear CustomerDo not place the Video Capture Docking Station AC Power Adapter/Charger How to handle a CD-ROMMaintenance Contents Save Picture Additional OperationsJlip Player Software Getting StartedAdvanced Operations Troubleshooting Major Specifications IndexVideo Printer Operation GV-PT2 Business presentations Major FeaturesInternet homepage Video journal and postcardsVideo Capture Facility Jlip Video Capture SoftwareJlip Control Facility Data Sharing With Jlip Player Soft- wareContro L S AN D Connec Tors Video output jack Outputs S-Video signal. Also Connections W hen Using JL IP Video Capture Software Input What is Jlip ? What is video capture software ?Operating Environment Connectable DevicesWindows Installation ProcedurePreparation Open & C Lose Bas ic Operatio n Proc edureClick Exit from File in the menu bar. The program closes HOW to Close the ProgramSelect Transfer Rate. Normally select Initializing JlipSelect Units Control buttons Main Desktop WindowMenu bar Image display area Menu BAREN H OW the Deskto P W ORK S Each pulldown menu is configured as follows00012312F VCR operation windowCapturing Video Images Image data flowIndex image data is transferred to the computer Step by Step CaptureFull image data is transferred to the computer Repeat steps 2 through 5 as requiredProgram Capture EN V Ideo CA PtureAutomatic Capture Transfer Automatically Interval CaptureSelecting a Picture Format Capture ModePicture Data Format EN Addi Tional Oper AT Ions Counter ResetCounter Value Change Modify Capture Point window appearsYou can change the Video Capture Unit’s ID number Delete Index Image and Full ImageChange ID Saving Create NEW FolderOpen the menu bar and click File New Album Saved, you will be asked whether to save or notSave the Full Image Data Open IndexEN Jlip Player Soft Ware Using Jlip Player Software DataMake sure all units are properly connected p Open Jlip jlp File window is displayedSave As Jlip jlp File window is displayed HOW to Store Jlip Player DataProblem Cause Where the program run file Counter cannot be resetCannot capture video data With the desired counterMessage Appears when Action Execute after ErrorPlaying back Not enough diskEN Memo Jlip Player Software Section EN Connections When Using Jlip Playe r Soft ware JVC Video unit Gettin G Started To start the setup program Installing Jlip Player Software ENSelect Serial Port Starting Jlip Player SoftwarePrepare Devices Select Devices Icon button Title barDisplay File nameElapsed Time MemoOperating camcorder Setting in/out pointsStart Playback Select SceneClick Start Only the camcorder movesDubbing Basic OP Eration SPrepare NEW Tape Start EditingEnter File Name Start SavingSave File Select Floppy Disk DriveCorrecting and cutting the programmed counter data EN BA SIC OP E RationsOpening a saved file Designateied Scene to be COP Overwriting the fileStore Designated Scene in Memory Designate Scene to be TransferredIcon button Position button Power buttonStore button Print buttonPosition button Content buttonMULTI-PIX button Strobe Speed buttonBring UP Video Printer Window PrintingPlayback Store SceneVideo Printer window closes Movie Player window closes Click Close Choose Exit from FilePreparation Auto CaptureTo Print Captured Video Data with Video Printer Load the tape into the video unitTo print only the cut-in scene on the edited tape Changing ID number Connecting other device during operationEN Advan CED Oper AT Ions Access Device Selection Dialog BOX Access Name Change Dialog BOXWhen Using the Video Capture Software Enter NEW Name SET NEW NameEN Advanc ED Operat Ions Access Pause Time CORREC- Tion Dialog BOXEnter Value Determine ValueThat power is on Error - This application willPower on all devices System Communication error Check devices - ConfirmAjor Speci Ficat Ions Automatic Capture Auto Bitmap Setup MenuChange ID COM Port Delete Index Image and Full Image Desktop Window Pg , 48GV-DS1