JVC 0397MKVUNSN, LYT0002-0H6B manual Access Name Change Dialog BOX, Enter NEW Name SET NEW Name

Page 63

Changing the name of the device

1 ACCESS "NAME CHANGE" DIALOG BOX

Choose "Name Change" from "File" on the MOVIE PLAYER window.

•The "Name Change" dialog box appears.

2 SELECT DEVICE

Click on the name of the device and "CHANGE".

•The dialog box to enter new name of the device appears.

3 ENTER NEW NAME

4 SET NEW NAME

Click "OK".

•The message "Device name will be changed." appears.

Clicking "OK" again sets that device name and brings up the "Name Change" dialog box.

5 RETURN TO MOVIE PLAYER WINDOW

Click "CLOSE".

Name Change

Select the device to change.

VCR

06:VCRCAMERA

CHANGE CLOSE

VIDEO PRINTER

CHANGE

Name Change

Enter new name (up to 20 letters).

06 = VCRCAMERA (1)

OK CANCEL

EN 63

Changing the device to use while connecting over two same type de- vices

1 ACCESS "DEVICE SELECTION" DIALOG BOX

Choose "Device Change" from "File" on the MOVIE PLAYER window.

•The "Device Selection" dialog box appears.

2 SELECT DEVICE

Click on the name of the device and "OK".

NOTE:

It is impossible to use two same type devices simultaneously.

	Device Selection
	Select Devices to control.
	VCR
	DISCONNECT	OK
	06:VCRCAMERA (1)	OK
	06:VCRCAMERA (1)
	07:VCRCAMERA (2)	CANCEL
		CANCEL
	VIDEO PRINTER
	DISCONNECT

When Using the Video Capture Software

The JLIP Player Software and JLIP Video Capture Software cannot run simultaneously. When you want to run the JLIP Video Capture Software, first select "Close Serial" from "File" on the menu bar. To resume using the JLIP Player Software, click the "JLIP" button in the JLIP Video Capture Software and select "Open Serial" from "File" on the JLIP Player Software's menu bar.

Image 63

Contents GV-DS1 It is recommended that you Dear CustomerDo not place the Video Capture Docking Station How to handle a CD-ROM MaintenanceAC Power Adapter/Charger Contents Getting Started Additional OperationsSave Picture Jlip Player SoftwareTroubleshooting Major Specifications Index Video Printer Operation GV-PT2Advanced Operations Video journal and postcards Major FeaturesBusiness presentations Internet homepageData Sharing With Jlip Player Soft- ware Jlip Video Capture SoftwareVideo Capture Facility Jlip Control FacilityContro L S AN D Connec Tors Video output jack Outputs S-Video signal. Also Connections W hen Using JL IP Video Capture Software Input Connectable Devices What is video capture software ?What is Jlip ? Operating EnvironmentWindows Installation ProcedurePreparation Open & C Lose Bas ic Operatio n Proc edureClick Exit from File in the menu bar. The program closes HOW to Close the ProgramSelect Transfer Rate. Normally select Initializing JlipSelect Units Main Desktop Window Menu barControl buttons Image display area Menu BAREN H OW the Deskto P W ORK S Each pulldown menu is configured as follows00012312F VCR operation windowCapturing Video Images Image data flowRepeat steps 2 through 5 as required Step by Step CaptureIndex image data is transferred to the computer Full image data is transferred to the computerEN V Ideo CA Pture Automatic CaptureProgram Capture Transfer Automatically Interval CaptureCapture Mode Picture Data FormatSelecting a Picture Format Modify Capture Point window appears Counter ResetEN Addi Tional Oper AT Ions Counter Value ChangeDelete Index Image and Full Image Change IDYou can change the Video Capture Unit’s ID number Saved, you will be asked whether to save or not Create NEW FolderSaving Open the menu bar and click File New AlbumSave the Full Image Data Open IndexOpen Jlip jlp File window is displayed Using Jlip Player Software DataEN Jlip Player Soft Ware Make sure all units are properly connected pSave As Jlip jlp File window is displayed HOW to Store Jlip Player DataProblem Cause With the desired counter Counter cannot be resetWhere the program run file Cannot capture video dataMessage Appears when Action Not enough disk ErrorExecute after Playing backEN Memo Jlip Player Software Section EN Connections When Using Jlip Playe r Soft ware JVC Video unit Gettin G Started To start the setup program Installing Jlip Player Software ENStarting Jlip Player Software Prepare DevicesSelect Serial Port Select Devices File name Title barIcon button DisplayElapsed Time MemoOperating camcorder Setting in/out pointsOnly the camcorder moves Select SceneStart Playback Click StartStart Editing Basic OP Eration SDubbing Prepare NEW TapeSelect Floppy Disk Drive Start SavingEnter File Name Save FileEN BA SIC OP E Rations Opening a saved fileCorrecting and cutting the programmed counter data Designate Scene to be Transferred Overwriting the fileDesignateied Scene to be COP Store Designated Scene in MemoryPrint button Position button Power buttonIcon button Store buttonStrobe Speed button Content buttonPosition button MULTI-PIX buttonStore Scene PrintingBring UP Video Printer Window PlaybackVideo Printer window closes Movie Player window closes Click Close Choose Exit from FileLoad the tape into the video unit Auto CapturePreparation To Print Captured Video Data with Video PrinterTo print only the cut-in scene on the edited tape Connecting other device during operation EN Advan CED Oper AT IonsChanging ID number Enter NEW Name SET NEW Name Access Name Change Dialog BOXAccess Device Selection Dialog BOX When Using the Video Capture SoftwareDetermine Value Access Pause Time CORREC- Tion Dialog BOXEN Advanc ED Operat Ions Enter ValueCheck devices - Confirm Error - This application willThat power is on Power on all devices System Communication errorAjor Speci Ficat Ions Delete Index Image and Full Image Desktop Window Pg , 48 Setup MenuAutomatic Capture Auto Bitmap Change ID COM PortGV-DS1