JVC LYT0002-0H6B, 0397MKVUNSN manual Basic OP Eration S, Dubbing, Prepare NEW Tape, Start Editing

Page 52

52EN

BASICOPERATIONS (cont.)

Dubbing

MOVIE PLAYER
File Edit Video Printer		Help
COUNTER Non Drop		00:01:30:10F		ID	06	FILE
POWER	ON OFF		MEMO
PROGRAM PLAYBACK			SCENE		STOP		MODE
SCENE	CUT IN		CUT OUT				STILL
01	00:01:30:12F		00:03:27:14F				PLAY
02	00:07:15:21F		00:10:40:18F				SEARCH
03	00:15:50:11F		00:20:33:10F				SLOW
							SLOW
							FF
ELAPSED TIME			00:10:04:28F				REW
ELAPSED TIME			00:10:04:28F
							IN/OUT
Rec On ! !

You can record all programmed scenes onto the tape in the recording deck.

Dubbing is possible only when the GR- DVM1or GR-DVM801 is connected. (as of March, 1997)

1 PREPARE NEW TAPE

Make sure the erase protection tab on the tape is present. Then insert it into the recording deck and set the recording deck to the Record-Pause mode.

2 START EDITING

Click "START" on the MOVIE PLAYER window.

When editing stops, the camcorder enters the Stop mode and the recording deck enters the Record-Pause mode.

•During dubbing, do no operation other than pressing "STOP". If other opera- tions are done, a malfunction may occur.

3 STOP EDITING Stop the recording deck.

NOTES:

●Also refer to the camcorder's instruction manual on dubbing.

●There may be small margin between the CUT IN/OUT points you input and the dubbed scenes' ones.

●Dubbing is impossible using a camcorder whose JLIP connector serves as an Edit jack.

Image 52

Contents GV-DS1 Dear Customer It is recommended that youDo not place the Video Capture Docking Station Maintenance How to handle a CD-ROMAC Power Adapter/Charger Contents Additional Operations Save PictureJlip Player Software Getting StartedVideo Printer Operation GV-PT2 Troubleshooting Major Specifications IndexAdvanced Operations Major Features Business presentationsInternet homepage Video journal and postcardsJlip Video Capture Software Video Capture FacilityJlip Control Facility Data Sharing With Jlip Player Soft- wareContro L S AN D Connec Tors Video output jack Outputs S-Video signal. Also Connections W hen Using JL IP Video Capture Software Input What is video capture software ? What is Jlip ?Operating Environment Connectable DevicesInstallation Procedure WindowsOpen & C Lose Bas ic Operatio n Proc edure PreparationHOW to Close the Program Click Exit from File in the menu bar. The program closesInitializing Jlip Select Transfer Rate. Normally selectSelect Units Menu bar Main Desktop WindowControl buttons Menu BAR Image display areaEach pulldown menu is configured as follows EN H OW the Deskto P W ORK SVCR operation window 00012312FImage data flow Capturing Video ImagesStep by Step Capture Index image data is transferred to the computerFull image data is transferred to the computer Repeat steps 2 through 5 as requiredAutomatic Capture EN V Ideo CA PtureProgram Capture Transfer Interval Capture AutomaticallyPicture Data Format Capture ModeSelecting a Picture Format Counter Reset EN Addi Tional Oper AT IonsCounter Value Change Modify Capture Point window appearsChange ID Delete Index Image and Full ImageYou can change the Video Capture Unit’s ID number Create NEW Folder SavingOpen the menu bar and click File New Album Saved, you will be asked whether to save or notOpen Index Save the Full Image DataUsing Jlip Player Software Data EN Jlip Player Soft WareMake sure all units are properly connected p Open Jlip jlp File window is displayedHOW to Store Jlip Player Data Save As Jlip jlp File window is displayedProblem Cause Counter cannot be reset Where the program run fileCannot capture video data With the desired counterMessage Appears when Action Error Execute afterPlaying back Not enough diskEN Memo Jlip Player Software Section EN Connections When Using Jlip Playe r Soft ware JVC Video unit Gettin G Started Installing Jlip Player Software EN To start the setup programPrepare Devices Starting Jlip Player SoftwareSelect Serial Port Select Devices Title bar Icon buttonDisplay File nameMemo Elapsed TimeSetting in/out points Operating camcorderSelect Scene Start PlaybackClick Start Only the camcorder movesBasic OP Eration S DubbingPrepare NEW Tape Start EditingStart Saving Enter File NameSave File Select Floppy Disk DriveOpening a saved file EN BA SIC OP E RationsCorrecting and cutting the programmed counter data Overwriting the file Designateied Scene to be COPStore Designated Scene in Memory Designate Scene to be TransferredPosition button Power button Icon buttonStore button Print buttonContent button Position buttonMULTI-PIX button Strobe Speed buttonPrinting Bring UP Video Printer WindowPlayback Store SceneClick Close Choose Exit from File Video Printer window closes Movie Player window closesAuto Capture PreparationTo Print Captured Video Data with Video Printer Load the tape into the video unitTo print only the cut-in scene on the edited tape EN Advan CED Oper AT Ions Connecting other device during operationChanging ID number Access Name Change Dialog BOX Access Device Selection Dialog BOXWhen Using the Video Capture Software Enter NEW Name SET NEW NameAccess Pause Time CORREC- Tion Dialog BOX EN Advanc ED Operat IonsEnter Value Determine ValueError - This application will That power is onPower on all devices System Communication error Check devices - ConfirmAjor Speci Ficat Ions Setup Menu Automatic Capture Auto BitmapChange ID COM Port Delete Index Image and Full Image Desktop Window Pg , 48GV-DS1