JVC 0397MKVUNSN manual HOW to Store Jlip Player Data, Save As Jlip jlp File window is displayed

Page 35

EN 35

HOW TO STORE JLIP PLAYER DATA

Data from this unit can be converted to JLIP Player software files.

If index image data is saved as a JLIP Player software file, the file can be printed with the optional GV-PT2 Video Printer.

Refer to the instruction manual for details.

File

New Album

Open Album

Save AlbumCtrl+S

Open JLIP (jlp) File

Save As JLIP (jlp) File

Save Image As…

Ctrl+A

Exit

Preparation

•Make sure all units are properly connected (☞ p. 12).

•Insert a video tape into the video source unit.

•If you want to store the data on a floppy disk, load a data disk into the floppy disk drive, create a directory and sub-directory on the data disk (☞ p. 54).

1 Open the menu bar and click "File" — "Save As JLIP (jlp) File".

•The "Save As JLIP (jlp) File" window is displayed.

2 Enter the folder name (directory) and file name.

•If you want to store the data on a floppy disk, enter the drive name.

3 Click "OK".

•The data converted to a JLIP Player software file is stored on the floppy disk in the selected drive.

•JLIP Player software files can be used for video program editing or printed with the video printer (☞ p. 58, 60).

NOTE : When stored data is opened with the JLIP Player software, the edit-in and edit-out points have the same counter value. When you want to perform program editing, change the counter number at the edit-out point in the JLIP Player software’s "Modify Edit Points".

Image 35

Contents GV-DS1 It is recommended that you Dear CustomerDo not place the Video Capture Docking Station AC Power Adapter/Charger How to handle a CD-ROMMaintenance Contents Getting Started Additional OperationsSave Picture Jlip Player SoftwareAdvanced Operations Troubleshooting Major Specifications IndexVideo Printer Operation GV-PT2 Video journal and postcards Major FeaturesBusiness presentations Internet homepageData Sharing With Jlip Player Soft- ware Jlip Video Capture SoftwareVideo Capture Facility Jlip Control FacilityContro L S AN D Connec Tors Video output jack Outputs S-Video signal. Also Connections W hen Using JL IP Video Capture Software Input Connectable Devices What is video capture software ?What is Jlip ? Operating EnvironmentWindows Installation ProcedurePreparation Open & C Lose Bas ic Operatio n Proc edureClick Exit from File in the menu bar. The program closes HOW to Close the ProgramSelect Transfer Rate. Normally select Initializing JlipSelect Units Control buttons Main Desktop WindowMenu bar Image display area Menu BAREN H OW the Deskto P W ORK S Each pulldown menu is configured as follows00012312F VCR operation windowCapturing Video Images Image data flowRepeat steps 2 through 5 as required Step by Step CaptureIndex image data is transferred to the computer Full image data is transferred to the computerProgram Capture EN V Ideo CA PtureAutomatic Capture Transfer Automatically Interval CaptureSelecting a Picture Format Capture ModePicture Data Format Modify Capture Point window appears Counter ResetEN Addi Tional Oper AT Ions Counter Value ChangeYou can change the Video Capture Unit’s ID number Delete Index Image and Full ImageChange ID Saved, you will be asked whether to save or not Create NEW FolderSaving Open the menu bar and click File New AlbumSave the Full Image Data Open IndexOpen Jlip jlp File window is displayed Using Jlip Player Software DataEN Jlip Player Soft Ware Make sure all units are properly connected pSave As Jlip jlp File window is displayed HOW to Store Jlip Player DataProblem Cause With the desired counter Counter cannot be resetWhere the program run file Cannot capture video dataMessage Appears when Action Not enough disk ErrorExecute after Playing backEN Memo Jlip Player Software Section EN Connections When Using Jlip Playe r Soft ware JVC Video unit Gettin G Started To start the setup program Installing Jlip Player Software ENSelect Serial Port Starting Jlip Player SoftwarePrepare Devices Select Devices File name Title barIcon button DisplayElapsed Time MemoOperating camcorder Setting in/out pointsOnly the camcorder moves Select SceneStart Playback Click StartStart Editing Basic OP Eration SDubbing Prepare NEW TapeSelect Floppy Disk Drive Start SavingEnter File Name Save FileCorrecting and cutting the programmed counter data EN BA SIC OP E RationsOpening a saved file Designate Scene to be Transferred Overwriting the fileDesignateied Scene to be COP Store Designated Scene in MemoryPrint button Position button Power buttonIcon button Store buttonStrobe Speed button Content buttonPosition button MULTI-PIX buttonStore Scene PrintingBring UP Video Printer Window PlaybackVideo Printer window closes Movie Player window closes Click Close Choose Exit from FileLoad the tape into the video unit Auto CapturePreparation To Print Captured Video Data with Video PrinterTo print only the cut-in scene on the edited tape Changing ID number Connecting other device during operationEN Advan CED Oper AT Ions Enter NEW Name SET NEW Name Access Name Change Dialog BOXAccess Device Selection Dialog BOX When Using the Video Capture SoftwareDetermine Value Access Pause Time CORREC- Tion Dialog BOXEN Advanc ED Operat Ions Enter ValueCheck devices - Confirm Error - This application willThat power is on Power on all devices System Communication errorAjor Speci Ficat Ions Delete Index Image and Full Image Desktop Window Pg , 48 Setup MenuAutomatic Capture Auto Bitmap Change ID COM PortGV-DS1