JVC LYT0002-0H6B, 0397MKVUNSN manual EN Connections When Using Jlip Playe r Soft ware

Page 42

42EN CONNECTIONS(WhenUsingJLIPPlayerSoftware)

WHEN CONNECTING TO A VIDEO SOURCE UNIT WITH JLIP CONNECTOR OR TO A VIDEO PRINTER

■Be sure to turn off the power of all connected units before making any connections.

■When connecting the provided cable, be sure to connect the plug with the Core Filter to the Video Capture Docking Station.

To COM port			To digital
To COM port			connector
(RS-232C)			(8 pin)

	PC connection	Core
		Filter
	cable (provided)

3.5 mm diameter

4-pole cable (provided)

When connected with the Video Printer

GV-PT2 Video Printer

Connect this if the video unit

To JLIP connector has an S-Video input connector

To S-Video input connector

To video input connector

S-Video cable

If you edit using a non-JVC VCR...

T W

It is possible to use the remote control unit provided with the GR-DVM1 and GR-DVM801. Also refer to the GR-DVM1’s or GR-DVM801’s instructions on connection and operation with your brand of VCR.

NOTE:

Some VCR brands or models cannot be operated.

RM-V708U or RM-V710U

Image 42

Contents GV-DS1 Dear Customer It is recommended that youDo not place the Video Capture Docking Station How to handle a CD-ROM MaintenanceAC Power Adapter/Charger Contents Jlip Player Software Additional OperationsSave Picture Getting StartedTroubleshooting Major Specifications Index Video Printer Operation GV-PT2Advanced Operations Internet homepage Major FeaturesBusiness presentations Video journal and postcardsJlip Control Facility Jlip Video Capture SoftwareVideo Capture Facility Data Sharing With Jlip Player Soft- wareContro L S AN D Connec Tors Video output jack Outputs S-Video signal. Also Connections W hen Using JL IP Video Capture Software Input Operating Environment What is video capture software ?What is Jlip ? Connectable DevicesInstallation Procedure WindowsOpen & C Lose Bas ic Operatio n Proc edure PreparationHOW to Close the Program Click Exit from File in the menu bar. The program closesInitializing Jlip Select Transfer Rate. Normally selectSelect Units Main Desktop Window Menu barControl buttons Menu BAR Image display areaEach pulldown menu is configured as follows EN H OW the Deskto P W ORK SVCR operation window 00012312FImage data flow Capturing Video ImagesFull image data is transferred to the computer Step by Step CaptureIndex image data is transferred to the computer Repeat steps 2 through 5 as requiredEN V Ideo CA Pture Automatic CaptureProgram Capture Transfer Interval Capture AutomaticallyCapture Mode Picture Data FormatSelecting a Picture Format Counter Value Change Counter ResetEN Addi Tional Oper AT Ions Modify Capture Point window appearsDelete Index Image and Full Image Change IDYou can change the Video Capture Unit’s ID number Open the menu bar and click File New Album Create NEW FolderSaving Saved, you will be asked whether to save or notOpen Index Save the Full Image DataMake sure all units are properly connected p Using Jlip Player Software DataEN Jlip Player Soft Ware Open Jlip jlp File window is displayedHOW to Store Jlip Player Data Save As Jlip jlp File window is displayedProblem Cause Cannot capture video data Counter cannot be resetWhere the program run file With the desired counterMessage Appears when Action Playing back ErrorExecute after Not enough diskEN Memo Jlip Player Software Section EN Connections When Using Jlip Playe r Soft ware JVC Video unit Gettin G Started Installing Jlip Player Software EN To start the setup programStarting Jlip Player Software Prepare DevicesSelect Serial Port Select Devices Display Title barIcon button File nameMemo Elapsed TimeSetting in/out points Operating camcorderClick Start Select SceneStart Playback Only the camcorder movesPrepare NEW Tape Basic OP Eration SDubbing Start EditingSave File Start SavingEnter File Name Select Floppy Disk DriveEN BA SIC OP E Rations Opening a saved fileCorrecting and cutting the programmed counter data Store Designated Scene in Memory Overwriting the fileDesignateied Scene to be COP Designate Scene to be TransferredStore button Position button Power buttonIcon button Print buttonMULTI-PIX button Content buttonPosition button Strobe Speed buttonPlayback PrintingBring UP Video Printer Window Store SceneClick Close Choose Exit from File Video Printer window closes Movie Player window closesTo Print Captured Video Data with Video Printer Auto CapturePreparation Load the tape into the video unitTo print only the cut-in scene on the edited tape Connecting other device during operation EN Advan CED Oper AT IonsChanging ID number When Using the Video Capture Software Access Name Change Dialog BOXAccess Device Selection Dialog BOX Enter NEW Name SET NEW NameEnter Value Access Pause Time CORREC- Tion Dialog BOXEN Advanc ED Operat Ions Determine ValuePower on all devices System Communication error Error - This application willThat power is on Check devices - ConfirmAjor Speci Ficat Ions Change ID COM Port Setup MenuAutomatic Capture Auto Bitmap Delete Index Image and Full Image Desktop Window Pg , 48GV-DS1