JVC LYT0002-0H6B, 0397MKVUNSN manual Contro L S AN D Connec Tors

Page 10

10EN

CONTROLSANDCONNECTORS

The controls and connectors marked * can be used only when the GR-DVM1 or GR-DVM801 Digital Camcorder is attached. For details of its operation, read the camcorder instruction manual.

* STOP button	* PLAY button
* Rewind (REW) button		* PAUSE button
* Fast-Forward (FF) button		* EDIT button
		* Lock lever
		* RELEASE button
		* DIGITAL jack ☞ p. 13
		•Connect to the computer’s
		RS-232C terminal (COM
		port).
* Multi connector		JLIP jack ☞ p. 13
•The Docking Station can be connected with		(joint Level Interface Protocol)
the GR-DVM1 or GR-DVM801 through this		•Connect to a JLIP-compatible
connector. Never touch it with your hand or		comcorder or VCR to control it
hit it with a hard object; if the pins are		from the computer.
damaged, the connectors will become
unusable due to contact failure.

Image 10

Contents GV-DS1 Dear Customer It is recommended that youDo not place the Video Capture Docking Station Maintenance How to handle a CD-ROMAC Power Adapter/Charger Contents Jlip Player Software Additional OperationsSave Picture Getting StartedVideo Printer Operation GV-PT2 Troubleshooting Major Specifications IndexAdvanced Operations Internet homepage Major FeaturesBusiness presentations Video journal and postcardsJlip Control Facility Jlip Video Capture SoftwareVideo Capture Facility Data Sharing With Jlip Player Soft- wareContro L S AN D Connec Tors Video output jack Outputs S-Video signal. Also Connections W hen Using JL IP Video Capture Software Input Operating Environment What is video capture software ?What is Jlip ? Connectable DevicesInstallation Procedure WindowsOpen & C Lose Bas ic Operatio n Proc edure PreparationHOW to Close the Program Click Exit from File in the menu bar. The program closesInitializing Jlip Select Transfer Rate. Normally selectSelect Units Menu bar Main Desktop WindowControl buttons Menu BAR Image display areaEach pulldown menu is configured as follows EN H OW the Deskto P W ORK SVCR operation window 00012312FImage data flow Capturing Video ImagesFull image data is transferred to the computer Step by Step CaptureIndex image data is transferred to the computer Repeat steps 2 through 5 as requiredAutomatic Capture EN V Ideo CA PtureProgram Capture Transfer Interval Capture AutomaticallyPicture Data Format Capture ModeSelecting a Picture Format Counter Value Change Counter ResetEN Addi Tional Oper AT Ions Modify Capture Point window appearsChange ID Delete Index Image and Full ImageYou can change the Video Capture Unit’s ID number Open the menu bar and click File New Album Create NEW FolderSaving Saved, you will be asked whether to save or notOpen Index Save the Full Image DataMake sure all units are properly connected p Using Jlip Player Software DataEN Jlip Player Soft Ware Open Jlip jlp File window is displayedHOW to Store Jlip Player Data Save As Jlip jlp File window is displayedProblem Cause Cannot capture video data Counter cannot be resetWhere the program run file With the desired counterMessage Appears when Action Playing back ErrorExecute after Not enough diskEN Memo Jlip Player Software Section EN Connections When Using Jlip Playe r Soft ware JVC Video unit Gettin G Started Installing Jlip Player Software EN To start the setup programPrepare Devices Starting Jlip Player SoftwareSelect Serial Port Select Devices Display Title barIcon button File nameMemo Elapsed TimeSetting in/out points Operating camcorderClick Start Select SceneStart Playback Only the camcorder movesPrepare NEW Tape Basic OP Eration SDubbing Start EditingSave File Start SavingEnter File Name Select Floppy Disk DriveOpening a saved file EN BA SIC OP E RationsCorrecting and cutting the programmed counter data Store Designated Scene in Memory Overwriting the fileDesignateied Scene to be COP Designate Scene to be TransferredStore button Position button Power buttonIcon button Print buttonMULTI-PIX button Content buttonPosition button Strobe Speed buttonPlayback PrintingBring UP Video Printer Window Store SceneClick Close Choose Exit from File Video Printer window closes Movie Player window closesTo Print Captured Video Data with Video Printer Auto CapturePreparation Load the tape into the video unitTo print only the cut-in scene on the edited tape EN Advan CED Oper AT Ions Connecting other device during operationChanging ID number When Using the Video Capture Software Access Name Change Dialog BOXAccess Device Selection Dialog BOX Enter NEW Name SET NEW NameEnter Value Access Pause Time CORREC- Tion Dialog BOXEN Advanc ED Operat Ions Determine ValuePower on all devices System Communication error Error - This application willThat power is on Check devices - ConfirmAjor Speci Ficat Ions Change ID COM Port Setup MenuAutomatic Capture Auto Bitmap Delete Index Image and Full Image Desktop Window Pg , 48GV-DS1

CONTROLSANDCONNECTORS

* Multi connector

JLIP jack ☞ p. 13