JVC LYT0002-0H6B, 0397MKVUNSN manual Gettin G Started

Page 44

44EN

GETTINGSTARTED

What is JLIP ?

JLIP* stands for Joint Level Interface Protocol, a new communication protocol which allows AV units equipped with a JLIP terminal to be controlled by a personal computer.

* is a registered trademark of JVC.

Operating Environment

●Personal computer with Microsoft® Windows® 3.1 or Windows® 95

●CPU Intel DX4™ or higher processor

●Minimum RAM requirement: more than 8 MB

●Available Hard Disk space of at least 8 MB

●Colour display capable of at least 640 x 480 pixels, 256 colours Recommended 1024 x 768, 16.77 Mil colours

●1 free serial transmission port, compatible with 9600 bps transmission rate, conneclable to RS-232C with 9 pin serial connector.

Recommended compatible with UART 16550A

●Mouse (Windows® compatible)

●CD-ROM drive

Note : An optional 9 pin serial conversion adapter is required for computers using serial communication port other than standard 9 pin.

*Microsoft® and Windows® are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

*Other product and company names included in this instruction manual are trademarks and/or registered trademarks of their respective holders.

Devices to connect to the VIDEO CAPTURE DOCKING STATION

●Camcorder equipped with JLIP connector

●Video printer equipped with JLIP connector, GV-PT2 (as of March, 1997)

Image 44

Contents GV-DS1 Dear Customer It is recommended that youDo not place the Video Capture Docking Station AC Power Adapter/Charger How to handle a CD-ROMMaintenance Contents Additional Operations Save PictureJlip Player Software Getting StartedAdvanced Operations Troubleshooting Major Specifications IndexVideo Printer Operation GV-PT2 Major Features Business presentationsInternet homepage Video journal and postcardsJlip Video Capture Software Video Capture FacilityJlip Control Facility Data Sharing With Jlip Player Soft- wareContro L S AN D Connec Tors Video output jack Outputs S-Video signal. Also Connections W hen Using JL IP Video Capture Software Input What is video capture software ? What is Jlip ?Operating Environment Connectable DevicesInstallation Procedure WindowsOpen & C Lose Bas ic Operatio n Proc edure PreparationHOW to Close the Program Click Exit from File in the menu bar. The program closesInitializing Jlip Select Transfer Rate. Normally selectSelect Units Control buttons Main Desktop WindowMenu bar Menu BAR Image display areaEach pulldown menu is configured as follows EN H OW the Deskto P W ORK SVCR operation window 00012312FImage data flow Capturing Video ImagesStep by Step Capture Index image data is transferred to the computerFull image data is transferred to the computer Repeat steps 2 through 5 as requiredProgram Capture EN V Ideo CA PtureAutomatic Capture Transfer Interval Capture AutomaticallySelecting a Picture Format Capture ModePicture Data Format Counter Reset EN Addi Tional Oper AT IonsCounter Value Change Modify Capture Point window appearsYou can change the Video Capture Unit’s ID number Delete Index Image and Full ImageChange ID Create NEW Folder SavingOpen the menu bar and click File New Album Saved, you will be asked whether to save or notOpen Index Save the Full Image DataUsing Jlip Player Software Data EN Jlip Player Soft WareMake sure all units are properly connected p Open Jlip jlp File window is displayedHOW to Store Jlip Player Data Save As Jlip jlp File window is displayedProblem Cause Counter cannot be reset Where the program run fileCannot capture video data With the desired counterMessage Appears when Action Error Execute afterPlaying back Not enough diskEN Memo Jlip Player Software Section EN Connections When Using Jlip Playe r Soft ware JVC Video unit Gettin G Started Installing Jlip Player Software EN To start the setup programSelect Serial Port Starting Jlip Player SoftwarePrepare Devices Select Devices Title bar Icon buttonDisplay File nameMemo Elapsed TimeSetting in/out points Operating camcorderSelect Scene Start PlaybackClick Start Only the camcorder movesBasic OP Eration S DubbingPrepare NEW Tape Start EditingStart Saving Enter File NameSave File Select Floppy Disk DriveCorrecting and cutting the programmed counter data EN BA SIC OP E RationsOpening a saved file Overwriting the file Designateied Scene to be COPStore Designated Scene in Memory Designate Scene to be TransferredPosition button Power button Icon buttonStore button Print buttonContent button Position buttonMULTI-PIX button Strobe Speed buttonPrinting Bring UP Video Printer WindowPlayback Store SceneClick Close Choose Exit from File Video Printer window closes Movie Player window closesAuto Capture PreparationTo Print Captured Video Data with Video Printer Load the tape into the video unitTo print only the cut-in scene on the edited tape Changing ID number Connecting other device during operationEN Advan CED Oper AT Ions Access Name Change Dialog BOX Access Device Selection Dialog BOXWhen Using the Video Capture Software Enter NEW Name SET NEW NameAccess Pause Time CORREC- Tion Dialog BOX EN Advanc ED Operat IonsEnter Value Determine ValueError - This application will That power is onPower on all devices System Communication error Check devices - ConfirmAjor Speci Ficat Ions Setup Menu Automatic Capture Auto BitmapChange ID COM Port Delete Index Image and Full Image Desktop Window Pg , 48GV-DS1