JVC LYT0002-0H6B, 0397MKVUNSN manual Initializing Jlip, Select Transfer Rate. Normally select

Page 18

18EN

INITIALIZATION

INITIALIZING JLIP

The first time you start the Video Capture software, JLIP initialization is required. This sets which of the computer’s COM ports (connector into which the RS-232C cable is plugged) is connected to the GV-DS1 JLIP Video Capture Docking Station. The initialization window automatically appears the first time you start the software after installation. Do not forget to carry out this JLIP initialization procedure. The JLIP must be initialized again whenever you connect a new image source or other unit to the JLIP Video Capture Docking Station.

1.

2.

3.

4.

5.

Start the JLIP Video Capture software.

The "JLIP Initialization" screen automatically appears.

Select "COM Port".

•COM1 through COM4 ports are available. Check to see which COM port is connected to the JLIP Video Capture Docking Station and select it.

Select "Transfer Rate". •Normally select 38400.

•38400 may not be available on some computers. When transmission errors take place during use, switch to 19200 or 9600. Image data transmission will be slower at these speeds.

Click "OK" . Call up the "JLIP Initialization" window and check the connected units.

JLIP Initialization
COM Port	COM 1

Transfer Rate

38400

OK

Cancel

NOTE : If you want to change a unit or COM port or Transfer Rate, select "Initialize" from "Set-up" in the menu bar to call up the "JLIP Initialization" window. Repeat this setting procedure.

If a connection is incorrect, a connected unit is not turned on, or the connection ID numbers overlap, the message "Connection error" appears. Click "OK" to return to the Main desktop.

Image 18

Contents GV-DS1 Dear Customer It is recommended that youDo not place the Video Capture Docking Station How to handle a CD-ROM MaintenanceAC Power Adapter/Charger Contents Jlip Player Software Additional OperationsSave Picture Getting StartedTroubleshooting Major Specifications Index Video Printer Operation GV-PT2Advanced Operations Internet homepage Major FeaturesBusiness presentations Video journal and postcardsJlip Control Facility Jlip Video Capture SoftwareVideo Capture Facility Data Sharing With Jlip Player Soft- wareContro L S AN D Connec Tors Video output jack Outputs S-Video signal. Also Connections W hen Using JL IP Video Capture Software Input Operating Environment What is video capture software ?What is Jlip ? Connectable DevicesInstallation Procedure WindowsOpen & C Lose Bas ic Operatio n Proc edure PreparationHOW to Close the Program Click Exit from File in the menu bar. The program closesInitializing Jlip Select Transfer Rate. Normally selectSelect Units Main Desktop Window Menu barControl buttons Menu BAR Image display areaEach pulldown menu is configured as follows EN H OW the Deskto P W ORK SVCR operation window 00012312FImage data flow Capturing Video ImagesFull image data is transferred to the computer Step by Step CaptureIndex image data is transferred to the computer Repeat steps 2 through 5 as requiredEN V Ideo CA Pture Automatic CaptureProgram Capture Transfer Interval Capture AutomaticallyCapture Mode Picture Data FormatSelecting a Picture Format Counter Value Change Counter ResetEN Addi Tional Oper AT Ions Modify Capture Point window appearsDelete Index Image and Full Image Change IDYou can change the Video Capture Unit’s ID number Open the menu bar and click File New Album Create NEW FolderSaving Saved, you will be asked whether to save or notOpen Index Save the Full Image DataMake sure all units are properly connected p Using Jlip Player Software DataEN Jlip Player Soft Ware Open Jlip jlp File window is displayedHOW to Store Jlip Player Data Save As Jlip jlp File window is displayedProblem Cause Cannot capture video data Counter cannot be resetWhere the program run file With the desired counterMessage Appears when Action Playing back ErrorExecute after Not enough diskEN Memo Jlip Player Software Section EN Connections When Using Jlip Playe r Soft ware JVC Video unit Gettin G Started Installing Jlip Player Software EN To start the setup programStarting Jlip Player Software Prepare DevicesSelect Serial Port Select Devices Display Title barIcon button File nameMemo Elapsed TimeSetting in/out points Operating camcorderClick Start Select SceneStart Playback Only the camcorder movesPrepare NEW Tape Basic OP Eration SDubbing Start EditingSave File Start SavingEnter File Name Select Floppy Disk DriveEN BA SIC OP E Rations Opening a saved fileCorrecting and cutting the programmed counter data Store Designated Scene in Memory Overwriting the fileDesignateied Scene to be COP Designate Scene to be TransferredStore button Position button Power buttonIcon button Print buttonMULTI-PIX button Content buttonPosition button Strobe Speed buttonPlayback PrintingBring UP Video Printer Window Store SceneClick Close Choose Exit from File Video Printer window closes Movie Player window closesTo Print Captured Video Data with Video Printer Auto CapturePreparation Load the tape into the video unitTo print only the cut-in scene on the edited tape Connecting other device during operation EN Advan CED Oper AT IonsChanging ID number When Using the Video Capture Software Access Name Change Dialog BOXAccess Device Selection Dialog BOX Enter NEW Name SET NEW NameEnter Value Access Pause Time CORREC- Tion Dialog BOXEN Advanc ED Operat Ions Determine ValuePower on all devices System Communication error Error - This application willThat power is on Check devices - ConfirmAjor Speci Ficat Ions Change ID COM Port Setup MenuAutomatic Capture Auto Bitmap Delete Index Image and Full Image Desktop Window Pg , 48GV-DS1