JVC 0397MKVUNSN manual Select Scene, Start Playback, Click Start, Only the camcorder moves

Page 51

EN 51

Playing back one programmed scene

MOVIE PLAYER								1
File Edit Video Printer		Help
COUNTER Non Drop		00:01:25:17F		ID	06	FILE
POWER	ON OFF		MEMO
POWER	ON OFF		MEMO
PROGRAM PLAYBACK			SCENE		STOP		MODE
SCENE	CUT IN		CUT OUT				STILL	2
01	00:01:30:12F		00:03:27:14F				PLAY
02	00:07:15:21F		00:10:40:18F				SEARCH
03	00:15:50:11F		00:20:33:10F				SLOW
							FF
ELAPSED TIME			00:10:04:28F				REW
ELAPSED TIME			00:10:04:28F
							IN/OUT
Scene playback is executing.

SELECT SCENE

Click on the line where the CUT IN/OUT points you want to preview are displayed and that line will be highlighted.

START PLAYBACK

Click "SCENE".

•The camcorder searches the scene by going to a point prior to the CUT IN point and starts playback at the CUT IN point. Playback stops after the CUT OUT point is passed.

MOVIE PLAYER
File Edit Video Printer		Help
COUNTER Non Drop		00:01:25:17F		ID	06	FILE
POWER	ON OFF		MEMO
PROGRAM PLAYBACK			SCENE		STOP		MODE
SCENE	CUT IN		CUT OUT				STILL
01	00:01:30:12F		00:03:27:14F				PLAY
02	00:07:15:21F		00:10:40:18F				SEARCH
03	00:15:50:11F		00:20:33:10F				SLOW
							SLOW
							FF
ELAPSED TIME			00:10:04:28F				REW
ELAPSED TIME			00:10:04:28F
							IN/OUT
Program playback is executing.

Playing back all programmed scenes

1 START PLAYBACK

Click "START".

•The camcorder plays back scenes in numerical order and stops immediately after the last scene's CUT OUT point.

•Only the camcorder moves.

NOTES:

●During playback of programmed scenes, do no operation other than pressing "STOP".

If other operations are done, a malfunction may occur.

●If "SCENE" or "START" is clicked at the end of tape, the camcorder will not function properly.

●If the source tape has a blank portion, scenes will not be edited properly.

Image 51

Contents GV-DS1 It is recommended that you Dear CustomerDo not place the Video Capture Docking Station How to handle a CD-ROM MaintenanceAC Power Adapter/Charger Contents Getting Started Additional OperationsSave Picture Jlip Player SoftwareTroubleshooting Major Specifications Index Video Printer Operation GV-PT2Advanced Operations Video journal and postcards Major FeaturesBusiness presentations Internet homepageData Sharing With Jlip Player Soft- ware Jlip Video Capture SoftwareVideo Capture Facility Jlip Control FacilityContro L S AN D Connec Tors Video output jack Outputs S-Video signal. Also Connections W hen Using JL IP Video Capture Software Input Connectable Devices What is video capture software ?What is Jlip ? Operating EnvironmentWindows Installation ProcedurePreparation Open & C Lose Bas ic Operatio n Proc edureClick Exit from File in the menu bar. The program closes HOW to Close the ProgramSelect Transfer Rate. Normally select Initializing JlipSelect Units Main Desktop Window Menu barControl buttons Image display area Menu BAREN H OW the Deskto P W ORK S Each pulldown menu is configured as follows00012312F VCR operation windowCapturing Video Images Image data flowRepeat steps 2 through 5 as required Step by Step CaptureIndex image data is transferred to the computer Full image data is transferred to the computerEN V Ideo CA Pture Automatic CaptureProgram Capture Transfer Automatically Interval CaptureCapture Mode Picture Data FormatSelecting a Picture Format Modify Capture Point window appears Counter ResetEN Addi Tional Oper AT Ions Counter Value ChangeDelete Index Image and Full Image Change IDYou can change the Video Capture Unit’s ID number Saved, you will be asked whether to save or not Create NEW FolderSaving Open the menu bar and click File New AlbumSave the Full Image Data Open IndexOpen Jlip jlp File window is displayed Using Jlip Player Software DataEN Jlip Player Soft Ware Make sure all units are properly connected pSave As Jlip jlp File window is displayed HOW to Store Jlip Player DataProblem Cause With the desired counter Counter cannot be resetWhere the program run file Cannot capture video dataMessage Appears when Action Not enough disk ErrorExecute after Playing backEN Memo Jlip Player Software Section EN Connections When Using Jlip Playe r Soft ware JVC Video unit Gettin G Started To start the setup program Installing Jlip Player Software ENStarting Jlip Player Software Prepare DevicesSelect Serial Port Select Devices File name Title barIcon button DisplayElapsed Time MemoOperating camcorder Setting in/out pointsOnly the camcorder moves Select SceneStart Playback Click StartStart Editing Basic OP Eration SDubbing Prepare NEW TapeSelect Floppy Disk Drive Start SavingEnter File Name Save FileEN BA SIC OP E Rations Opening a saved fileCorrecting and cutting the programmed counter data Designate Scene to be Transferred Overwriting the fileDesignateied Scene to be COP Store Designated Scene in MemoryPrint button Position button Power buttonIcon button Store buttonStrobe Speed button Content buttonPosition button MULTI-PIX buttonStore Scene PrintingBring UP Video Printer Window PlaybackVideo Printer window closes Movie Player window closes Click Close Choose Exit from FileLoad the tape into the video unit Auto CapturePreparation To Print Captured Video Data with Video PrinterTo print only the cut-in scene on the edited tape Connecting other device during operation EN Advan CED Oper AT IonsChanging ID number Enter NEW Name SET NEW Name Access Name Change Dialog BOXAccess Device Selection Dialog BOX When Using the Video Capture SoftwareDetermine Value Access Pause Time CORREC- Tion Dialog BOXEN Advanc ED Operat Ions Enter ValueCheck devices - Confirm Error - This application willThat power is on Power on all devices System Communication errorAjor Speci Ficat Ions Delete Index Image and Full Image Desktop Window Pg , 48 Setup MenuAutomatic Capture Auto Bitmap Change ID COM PortGV-DS1