JVC 0397MKVUNSN, LYT0002-0H6B manual Delete Index Image and Full Image, Change ID

Page 31

•This completes the ID number change.

EN 31

DELETE INDEX IMAGE AND FULL IMAGE

You can delete any captured picture. Both index image (80 x 60 pixels) and full image (768 x 552 pixels) are deleted.

02

00:02:17:21

Edit

Transfer the Index Image

Transfer the Full Image

Modify…

DeleteDel

Window

Arrange Index

VCR

1 Click the image display box you want to delete.

•The box is bordered in green.

2 Open the menu bar and click "Edit" — "Delete".

•This deletes the selected image data.

3 Then click "Window" — "Arrange Index".

•This removes the deleted index image’s space and renumbers the remaining index display box. You can still run the program without re-arranging the index.

CHANGE ID

You can change the Video Capture Unit’s ID number.

Set-up

Capture Mode

Image Format

Device Change

Initialize

ID Change

Counter Reset

1 Open the menu bar and click "Set-up" — "ID Change".

•ID Change window appears.

2 Enter a new ID number.

3 Click "OK".

4 Open the menu bar and click "Set-up" — "Initialize".

•The "JLIP Initialization" window appears.

•Start JLIP initialization (☞ p. 18, 19).

Image 31

Contents GV-DS1 It is recommended that you Dear CustomerDo not place the Video Capture Docking Station Maintenance How to handle a CD-ROMAC Power Adapter/Charger Contents Getting Started Additional OperationsSave Picture Jlip Player SoftwareVideo Printer Operation GV-PT2 Troubleshooting Major Specifications IndexAdvanced Operations Video journal and postcards Major FeaturesBusiness presentations Internet homepageData Sharing With Jlip Player Soft- ware Jlip Video Capture SoftwareVideo Capture Facility Jlip Control FacilityContro L S AN D Connec Tors Video output jack Outputs S-Video signal. Also Connections W hen Using JL IP Video Capture Software Input Connectable Devices What is video capture software ?What is Jlip ? Operating EnvironmentWindows Installation ProcedurePreparation Open & C Lose Bas ic Operatio n Proc edureClick Exit from File in the menu bar. The program closes HOW to Close the ProgramSelect Transfer Rate. Normally select Initializing JlipSelect Units Menu bar Main Desktop WindowControl buttons Image display area Menu BAREN H OW the Deskto P W ORK S Each pulldown menu is configured as follows00012312F VCR operation windowCapturing Video Images Image data flowRepeat steps 2 through 5 as required Step by Step CaptureIndex image data is transferred to the computer Full image data is transferred to the computerAutomatic Capture EN V Ideo CA PtureProgram Capture Transfer Automatically Interval CapturePicture Data Format Capture ModeSelecting a Picture Format Modify Capture Point window appears Counter ResetEN Addi Tional Oper AT Ions Counter Value ChangeChange ID Delete Index Image and Full ImageYou can change the Video Capture Unit’s ID number Saved, you will be asked whether to save or not Create NEW FolderSaving Open the menu bar and click File New AlbumSave the Full Image Data Open IndexOpen Jlip jlp File window is displayed Using Jlip Player Software DataEN Jlip Player Soft Ware Make sure all units are properly connected pSave As Jlip jlp File window is displayed HOW to Store Jlip Player DataProblem Cause With the desired counter Counter cannot be resetWhere the program run file Cannot capture video dataMessage Appears when Action Not enough disk ErrorExecute after Playing backEN Memo Jlip Player Software Section EN Connections When Using Jlip Playe r Soft ware JVC Video unit Gettin G Started To start the setup program Installing Jlip Player Software ENPrepare Devices Starting Jlip Player SoftwareSelect Serial Port Select Devices File name Title barIcon button DisplayElapsed Time MemoOperating camcorder Setting in/out pointsOnly the camcorder moves Select SceneStart Playback Click StartStart Editing Basic OP Eration SDubbing Prepare NEW TapeSelect Floppy Disk Drive Start SavingEnter File Name Save FileOpening a saved file EN BA SIC OP E RationsCorrecting and cutting the programmed counter data Designate Scene to be Transferred Overwriting the fileDesignateied Scene to be COP Store Designated Scene in MemoryPrint button Position button Power buttonIcon button Store buttonStrobe Speed button Content buttonPosition button MULTI-PIX buttonStore Scene PrintingBring UP Video Printer Window PlaybackVideo Printer window closes Movie Player window closes Click Close Choose Exit from FileLoad the tape into the video unit Auto CapturePreparation To Print Captured Video Data with Video PrinterTo print only the cut-in scene on the edited tape EN Advan CED Oper AT Ions Connecting other device during operationChanging ID number Enter NEW Name SET NEW Name Access Name Change Dialog BOXAccess Device Selection Dialog BOX When Using the Video Capture SoftwareDetermine Value Access Pause Time CORREC- Tion Dialog BOXEN Advanc ED Operat Ions Enter ValueCheck devices - Confirm Error - This application willThat power is on Power on all devices System Communication errorAjor Speci Ficat Ions Delete Index Image and Full Image Desktop Window Pg , 48 Setup MenuAutomatic Capture Auto Bitmap Change ID COM PortGV-DS1