JVC 0397MKVUNSN, LYT0002-0H6B manual Memo, Elapsed Time

Page 49

1.COUNTER system

2.Tape counter display

• Displays actual tape position.

ex.

00: 01: 45: 10F (Hours : Minutes : Seconds : Frames)

3.ID number

•Displays the selected device's ID number.

4.FILE name

•Displays file name after saving the program under a new name.

ex. travel

5.POWER button

•Turns the device on and off.

•If power is not supplied to the camcorder beforehand, you can not turn the camcorder on and off by clicking this button.

•Some camcorders cannot be turned on and off by clicking this button.

6.MEMO

•If you wish to add some comment to the file, you can input it.

ex. Europe Tour

7.IN/OUT point display

•You can set up to 99 in/out points per file.

8.START button

•Starts editing. Scenes are recorded in scene's numerical order. After starting editing, this button changes to STOP button.

9.ELAPSED TIME

•Displays the total elapsed time of all the programmed scenes.

EN 49

10.Camcorder's operation buttons

• Operate the camcorder.

Stop button

REW/REW Search button

Play button

FF/FF Search button

Pause button

Reverse Slow button

Forward Slow button

•To start Reverse/Forward Slow-motion Search, first click the Pause button and then the Reverse/Forward Slow button.

•Functions your camcorder does not have cannot be performed by the above buttons.

•Click "File" — "Open VCR Control Window" on menubar to call up the "VCR Control" window. You can control the video source unit from this window.

11.MODE display

•Displays the camcorder's mode when operating the above buttons.

12.SCENE button

•Plays back only one programmed scene so that you can preview it.

•Operates only the camcorder.

13.IN/OUT point button

•Registers the cut-in and -out points of the scene you want to dub.

14.Message display

•Displays the connected device mode, etc.

To exit from the MOVIE PLAYER window, choose "Exit" from "File".

NOTE:

If you need the "MOVIE PLAYER HELP" window, choose "Contents" from "Help".

Image 49

Contents GV-DS1 It is recommended that you Dear CustomerDo not place the Video Capture Docking Station Maintenance How to handle a CD-ROMAC Power Adapter/Charger Contents Save Picture Additional OperationsJlip Player Software Getting StartedVideo Printer Operation GV-PT2 Troubleshooting Major Specifications IndexAdvanced Operations Business presentations Major FeaturesInternet homepage Video journal and postcardsVideo Capture Facility Jlip Video Capture SoftwareJlip Control Facility Data Sharing With Jlip Player Soft- wareContro L S AN D Connec Tors Video output jack Outputs S-Video signal. Also Connections W hen Using JL IP Video Capture Software Input What is Jlip ? What is video capture software ?Operating Environment Connectable DevicesWindows Installation ProcedurePreparation Open & C Lose Bas ic Operatio n Proc edureClick Exit from File in the menu bar. The program closes HOW to Close the ProgramSelect Transfer Rate. Normally select Initializing JlipSelect Units Menu bar Main Desktop WindowControl buttons Image display area Menu BAREN H OW the Deskto P W ORK S Each pulldown menu is configured as follows00012312F VCR operation windowCapturing Video Images Image data flowIndex image data is transferred to the computer Step by Step CaptureFull image data is transferred to the computer Repeat steps 2 through 5 as requiredAutomatic Capture EN V Ideo CA PtureProgram Capture Transfer Automatically Interval CapturePicture Data Format Capture ModeSelecting a Picture Format EN Addi Tional Oper AT Ions Counter ResetCounter Value Change Modify Capture Point window appearsChange ID Delete Index Image and Full ImageYou can change the Video Capture Unit’s ID number Saving Create NEW FolderOpen the menu bar and click File New Album Saved, you will be asked whether to save or notSave the Full Image Data Open IndexEN Jlip Player Soft Ware Using Jlip Player Software DataMake sure all units are properly connected p Open Jlip jlp File window is displayedSave As Jlip jlp File window is displayed HOW to Store Jlip Player DataProblem Cause Where the program run file Counter cannot be resetCannot capture video data With the desired counterMessage Appears when Action Execute after ErrorPlaying back Not enough diskEN Memo Jlip Player Software Section EN Connections When Using Jlip Playe r Soft ware JVC Video unit Gettin G Started To start the setup program Installing Jlip Player Software ENPrepare Devices Starting Jlip Player SoftwareSelect Serial Port Select Devices Icon button Title barDisplay File nameElapsed Time MemoOperating camcorder Setting in/out pointsStart Playback Select SceneClick Start Only the camcorder movesDubbing Basic OP Eration SPrepare NEW Tape Start EditingEnter File Name Start SavingSave File Select Floppy Disk DriveOpening a saved file EN BA SIC OP E RationsCorrecting and cutting the programmed counter data Designateied Scene to be COP Overwriting the fileStore Designated Scene in Memory Designate Scene to be TransferredIcon button Position button Power buttonStore button Print buttonPosition button Content buttonMULTI-PIX button Strobe Speed buttonBring UP Video Printer Window PrintingPlayback Store SceneVideo Printer window closes Movie Player window closes Click Close Choose Exit from FilePreparation Auto CaptureTo Print Captured Video Data with Video Printer Load the tape into the video unitTo print only the cut-in scene on the edited tape EN Advan CED Oper AT Ions Connecting other device during operationChanging ID number Access Device Selection Dialog BOX Access Name Change Dialog BOXWhen Using the Video Capture Software Enter NEW Name SET NEW NameEN Advanc ED Operat Ions Access Pause Time CORREC- Tion Dialog BOXEnter Value Determine ValueThat power is on Error - This application willPower on all devices System Communication error Check devices - ConfirmAjor Speci Ficat Ions Automatic Capture Auto Bitmap Setup MenuChange ID COM Port Delete Index Image and Full Image Desktop Window Pg , 48GV-DS1