Tyco Electronics P5400 manual P5450 Model Radio

Page 56

MM-012099-001, Rev. B

Overdial operation can also be used to initiate a telephone interconnect call via DTMF signaling if a dial tone has already been accessed on the system. This method makes a telephone interconnect call while operating in the conventional mode but will also function in trunked mode if a dial tone is directly accessible.

Telephone numbers and other number sequences for overdialing can be stored in the phone list when programming the radio. These numbers are accessed by pressing the key, then following the selection mode rules. Perform the following procedures to access and dial these stored numbers.

P5450 Model Radio

1.Follow the procedure in Section 8.23.2 to establish a connection to the telephone system or consult the system administrator for the procedure to access a dial tone on the trunked or conventional system.

2.Enter selection mode first to enable entry of Overdial numbers by pressing the button.

3.Follow the selection mode rules to call up a stored number from the phone list: Use the or

buttons to scroll through the list of stored numbers. is displayed. Press the PTT to send the overdial sequence once. If the number needs to be transmitted again it must be selected or entered again (this prevents unwanted numbers from being sent the next time the PTT button is pressed during the call).

Overdial select/entry mode remains active until the call is dropped, cleared, or is pressed. The overdial select/entry mode can be re-entered if the call is still active by pressing .

P5470 Model Radio

1.Follow the procedure in Section 8.23.2 to establish a connection to the telephone system or consult the system administrator for the procedure to access a dial tone on the trunked or conventional system.

2.Overdial numbers are transmitted using one of the following methods:

METHOD 1: 1. Enter the overdial selection mode by pressing the button.

2.Use the or buttons to scroll through the list of stored numbers. is displayed. Press the PTT to send the overdial sequence once. If the number needs to be transmitted again it must be selected or entered again (this prevents unwanted numbers from being sent the next time the PTT button is pressed during the call).

Overdial select/entry mode remains active until the call is dropped, cleared, or is pressed. The overdial select/entry mode can be re-entered if the call is still active by pressing .

56

Image 56
Contents P5400 Series MM-012099-001, Rev. B Table of Contents Menu 28.1 10.8.1 116 117Tables Safety Section Safety Conventions Safety Training Information RF Exposure GuidelinesRF Exposure Compliance Testing Distances Electromagnetic INTERFERENCE/COMPATIBILITYAntenna Care and Replacement Operating TipsEfficient Radio Operation Electronic DevicesPotentially Explosive Atmospheres AircraftElectric Blasting Caps Conditioning Battery Packs Conditioning NiMH Battery PacksConditioning NiCD Battery Packs BatteriesCharging Battery Packs Battery Pack UsageAdditional Information Charging GuidelinesChanging the Battery Pack Removing the Battery PackBattery Disposal Attaching the Battery PackProduct Information Introduction Water ResistanceOptions and Accessories Options and AccessoriesCarrying Case Accessories User Interface P5400 Portable RadioControls Buttons and KnobsKeypad P5450 Scan Model Front Panel P5400 Front Keypad FunctionsSample Display Edacs Mode DisplayRadio Status Icons Status Icons DescriptionsUniversal Device Connector Tri-Color LEDThis page intentionally left blank Edacs Operation Power ON-OFF Volume Knob Edacs OperationP5450 Scan Radio Front Panel P5450 Keypad Functions KEY Function Radio Display in Edacs Mode DisplayRadio Status Icons Status Icon DescriptionsTRI-COLOR LED Status MessagesError Messages Alert Tones Turning on the RadioSystem Selection Alert Tones11.1 P5470 Model GROUP/CHANNEL SelectionModify Scan List 11.2 P5450 Model Menu Item Selection ProcessBacklight Menu Item Selection Parameter Menu Item InformationFeature Display Parameter Setting Information DisplayContrast Adjust HIGH/LOW Power AdjustmentBacklight ON/OFF Declaring AN EmergencyUsing the Menu Button Using the Pre-Programmed Option ButtonClear Mode Digital ModePrivate Mode System Encryption Key DisplayPrivate Operation Receiving an Encrypted CallScanning Trunked Groups Turning Scan On and OffAdding Groups to a Scan List P5450 Model RadioP5470 Model Radio Scanning Trunked Systems Deleting Groups from a Scan ListNuisance Delete Wide Area System ScanningEmergency Operation Priority System ScanProScan Receiving an Emergency CallReceiving and Responding to an Individual Call Individual CallsDeclaring an Emergency Call Sending an Individual Call 11 Calls Received ListsReceiving a Telephone Interconnect Call Telephone Interconnect CallsCall Storage Lists Dual-Tone Multi-Frequency Overdial/Conventional Mode Sending a Telephone Interconnect CallP5450 Model Radio Method 2 P5470 model radios only Programmable EntriesSTATUS/MESSAGE Operation Status Operation Message OperationDynamic Regroup Operation Macro KEY OperationPortable Data Emergency OperationScan Lockout Mode DisplaysData OFF Operation Data on OperationData Lockout Mode This page intentionally left blank Conventional Operation Conventional Operation Power ON-OFF Volume Knob Voice Group Selection Control Knob P5450 Scan Radio Front Panel P5470 System Radio Front Panel Radio Display Battery Charge Icons Full Cycle Radio Status IconsMode no repeater Error Messages Name Tone Description1 P5470 Model MethodNuisance Delete 2 P5450 ModelBacklight Menu Item Parameter Only. No user selectable settings LID in EDACS/EA. In Conv it has no Using the Menu Button Using the Pre-Programmed Option ButtonReceiving a Call Sending a Call This page intentionally left blank P25 Operation 10 P25 Operation Voice Group Selection Control Knob EMERGENCY/ Home Button Enter key P5470 System Radio Front Panel Display Display Descriptions TRI-COLOR LED Error Messages Call queued for processing GROUP/CHANNEL Selection 10.9.1 P5470 Model10.9.2 P5450 Model Selectable settings Select Telephone Press Digital Voice Operation 11 System Encryption Key Display Group Clear Digital Private Programming Receive Transmit Scanning Trunked Groups 100 101 102 103 104 105 106 107 108 109 110 Transmitting a Group Call Group Calls in P25 ModeExiting Data Calls Individual Calls in P25 Mode Emergency Group Calls in P25 ModeReceiving an Emergency Group Call 114 Technical Assistance Warranty Information Technical Assistance Basic Troubleshooting TroubleshootingBattery Warranty 119 Tyco Electronics Wireless Systems Segment