Lincoln Electric LN-9F GMA manual Connecting the GUN CAbLE to the Wire Feeder, For GMA GUN CAbLES

Page 22

A-13

A-13

INSTALLATION

CONNECTING THE GUN CAbLE TO THE WIRE FEEDER

A variety of gun and cable assemblies are available for the LN-9 GMA models. See the Accessories section of this manual.

Lay the cable out straight. Insert the connector on the welding conductor cable into the brass conductor block on the front of the wire drive unit. See Figure A.10. Make sure the connector is fully seated and tighten the plastic thumbscrew. Keep this connection clean and bright. Connect the control cable polarized Amphenol plug into the mating 5-cavity receptacle on the front panel of the wire drive section.

FOR GMA GUN CAbLES:

Install the barbed fitting and union nut to the 5/8-18 female inert gas fitting on the front of the LN-9 GMA wire drive section. Connect the 3/16" I.D. gas hose from the gun cable to the barbed fitting.

When you remove the gun, you can easily detach this fitting by loosening the union nut.

FIGURE A.10 – GUN CAbLE CONNECTIONS

Thumb- screw

LN-9 GMA and LN-9F GMA Wire Feeder

Image 22

Contents LN-9 GMA and LN-9F GMA Wire Feeder Safety Depends on YouSafety Electric Shock can kill Welding and Cutting Sparks can Cause fire or explosion IiiPrécautions DE Sûreté Thank You TAbLE of Contents TAbLE OF CONTENTS cont’d Section F ViiiSection E P127, P125, P107 & P289 SeriesLN-9 GMA and LN-9F GMA Wire Feeder Technical SpecificationsWidth Height Mounting the Wire Feed Unit Installing the LN-9 GMA Roll and 4-ROLL ModelsAttaching the Wire Reel Stand Mounting the UnitElectrical Connections LN-9 GMA and LN-9F GMA Power Input CAbLE ASSEMbLYRouting the Electrode Figure A.2 Strain Relief Clamp Figure A.3 LN-9F GMA Control bOXInstallation Can kill Figure A.5 Connection of LN-9 GMA to DC-600 Power Sources Figure A.6 Connection of LN-9 GMA to DC-1000 Power Sources 75 76 77 Installation Figure A.9 Connection of LN-9 GMA to V300 Power Sources Machine Grounding Direct Work Lead ConnectionConnecting the GUN CAbLE to the Wire Feeder For GMA GUN CAbLESHooking UP GMA Shielding GAS Cylinder may explode if damagedSafety Precautions Operating InstructionsK424 LN-9 GMA 2-ROLL and K568-1 LN-9 GMA 4-ROLL General DescriptionRecommended Processes and Equipment K436 LN-9F GMA 2-ROLL and K583-1 LN-9F GMA 4-ROLLDC Constant Voltage Power Sources Controls and Settings Operation Operation Avoiding Grounding Lead Protector GLP Shutdown Power Supply FuseCircuit Protection and Automatic Shutdown Circuit bREAKERAutomatic Shutdown Drive Roll Installation Changing Drive Rolls for 2-ROLL Wire FeedersGuide Tube Detail Changing Drive Rolls for 4-ROLL Wire Feeders Large Wire Loading Figure b.7a Threaded Locking CollarLoading a 50-60 Lb .7-27.2 KG. Coil Using K1504-1 Coil Reel Feeding Electrode and bRAKE AdjustmentADJUSTAbLE Wire Reel bRAKE Loading a 50 or 60 Lb. CoilLoading and Feeding 13-14 Lb Innershield Coils K378 Reel Mounting StandRoll Wire Feeders Idle Roll Pressure SettingFor TWO-ROLL Feeders Pressure Adjustment Knob Pulse Power 500, DC650 PRO CV-400, CV-500-I Adjust the Power SourceAdjust the LN-9 GMA Controls DC-250, DC-400, or DC-600Voltage Control Response Starting CharacteristicsRUN-IN Feature Select AccelerationSecurity of Weld Procedure Settings Procedure AT END of CoilMaking a Weld Wire Reel Stands and Mountings Optional Equipment and AccessoriesPower Input CAbLE ASSEMbLIES K196, K595, K596 Auxiliary Equipment ContactsSpindle for READI-REELS and 2 I.D. Spools K162-H Attaching the Wire Reel StandsWire Reel Door KIT READI-REEL AdaptersUniversal Wire Reel Stand K1524-1 Wire Feeder Accessories BURNbACK Timer KIT K419Dual Procedure KIT K319 GMA Timer KIT K418Dual Process KIT K317 For Wire Feeders Pulse Power Filter Conversion KIT K442-1Continuous Flux Feed Tank K320 Swivel Platform K178-1Undercarriage K163 K320 Flux Tank LoadingK58 Magnetic Separator Cored Electrode TAbLE C.2 Drive Roll and Guide TUbE KitsKit Roll Solid Steel Electrode Aluminum ElectrodeCoils with 1 Spindle Routine MaintenancePeriodic Maintenance AdapterProper Speed Sensor Module Mounting Figure D.1 Speed Sensor Module LocationFigure D.2 LN-9 GMA Connectors Figure D.2 Switch RequirementsTROUbLESHOOTING TROUbLESHOOTING Guide Wire Feeding PRObLEMSGun trigger will not feed wire. Digital meter is not lit Grounding Lead Protector Shutdown in the Operation section TROUbLESHOOTING Welding PRObLEMS Starting Characteristics LN-9 GMA WIRING WireLN-9F GMA LN-9 GMA Dimension Print LN-9F GMA Dimension Print 1 Wire Drive Unit LN-9F Dimension Print 2 Control bOXPage Precaucion LN-9 GMA Wire Feeder Keep your head out of fumes