Lincoln Electric IM536-D manual GUN Handle Parts, Figure D.3 SP-125 Plus

Page 40

D-5

 

 

MAINTENANCE

 

 

 

 

 

 

 

 

 

GUN HANDLE PARTS

 

 

 

The gun handle consists of two halves that are held together with a collar on each end. To open up the handle, turn the collars approximately 60 degrees counter-clockwise until the collar reaches a stop. Then pull the collar off the gun handle. If the collars are diffi- cult to turn, position the gun handle against a corner, place a screwdriver against the tab on the collar and give the screwdriver a sharp blow to turn the collar past an internal locking rib. See Figure D-3.

Counter-clockwise

FIGURE D.3

SP-125 PLUS

Page 39 Page 41
Image 40
Page 39 Page 41
Contents SP-125 Plus Safety California Proposition 65 WarningsElectric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcThank You Please Examine Carton and Equipment For Damage ImmediatelyTable of Contents Vii Installation Identify and Locate Components Safety PrecautionsElectric Shock can kill Work Clamp Installation Work Cable InstallationSelect Suitable Location StackingConnecting Gun Cable to the SP-125 Plus GUN InstallationGAS Connection Gas Solenoid Inlet Fitting Power Input Cable Input ConnectionsCode Requirements for Input Connections Requirements For Rated OutputRequirements For Maximum Output Requirements For CSA Rated OutputObserve all safety information throughout this manual OperationFumes and Gases can be dangerous Welding Sparks can cause fire or explosionControls and Settings Design Features AdvantagesGeneral Description Welding CapabilityWelding Operations Wire LoadingSequence of Operation Friction Brake Adjustments Wire ThreadingShielding Gas Making a WeldCleaning Tip And Nozzle Changing Machine Over to Feed Other Wire SizesProcess Guidelines Wire Feed Overload Protection Overload ProtectionOutput Overload Thermal ProtectionLearning to Weld Learning to WeldARC-WELDING Circuit SELF-SHIELDED Fcaw Welding ARCProcess Selection Gmaw MIG Welding ARCFor Gmaw MIG Process Common Metals Joint Types and PositionsFor Fcaw Innershield Process Butt WeldsPenetration Welding In The Vertical PositionFillet Welds Machine SET UP for the SELF-SHIELDED Fcaw Process Welding Techniques for the SELF- Shielded Fcaw ProcessVertical-down Welding Correct Welding PositionCorrect Electrical Stickout ESO Correct Welding SpeedHelpful Hints PracticeMachine SET UP for the Gmaw MIG Process Welding Techniques for the Gmaw MIG ProcessFigure B.24 Troubleshooting Welds To Eliminate a Ropy Convex Bead in order of importanceTo Correct Poor Penetration in order of impor- tance To Eliminate Stubbing* in order of importanceProper Gun Handling Application Chart Accessories Optional AccessoriesK1799-1 Argon-Mixed Gas Adjustable Regulator and Hose Kit K586-1 Deluxe Adjustable Gas Regulator Hose KitReplacement Parts Innershield Fcaw ConversionMaintenance Maintenance Safety PrecautionsItems Requiring no Maintenance Routine and Periodic MAINTE- NanceGUN and Cable Maintenance Configuration of Components in Wire Feeding SystemFor Magnum 100L GUN Contact Tip Cable Liner Drive RollChanging the Contact TIP Changing Drive RollChanging Liner Liner trim length for gun with red trigger Magnum 100LGUN Handle Parts Figure D.3 SP-125 PlusTroubleshooting HOW to USE Troubleshooting GuideProblems Possible Areas Symptoms Misadjustments Troubleshooting GuideRecommended Course of Action Feeding Problems Welding Problems Wiring Diagrams SP-125 PlusSP-125 Plus SP-125 Plus How To Read Shop Drawings New Lessons in Arc WeldingNeed Welding Training? $700.00Precaucion Warnung
Top Page Image Contents